Your Vehicles As They Sit Now
#7261
General & Tech Moderator
MY350Z.COM
MY350Z.COM
Nice looking Z!
The following users liked this post:
MM'08_350Z (01-19-2016)
The following users liked this post:
MM'08_350Z (01-19-2016)
The following users liked this post:
MM'08_350Z (01-19-2016)
The following users liked this post:
NA&CH (01-19-2016)
#7269
350Z/370Z Tech Moderator
MY350Z.COM
MY350Z.COM
#7271
Super Moderator
MY350Z.COM
MY350Z.COM
#7274
350Z/370Z Tech Moderator
MY350Z.COM
MY350Z.COM
It appears that El Nino may actually be taking shape here in NorCal.
End of drought? Won't know until snowpack is measured later this spring. But from the looks of the reservoirs viewed this past weekend, a good sign as much of the dried vegetation that has been on the "banks" of same are now under water.
End of drought? Won't know until snowpack is measured later this spring. But from the looks of the reservoirs viewed this past weekend, a good sign as much of the dried vegetation that has been on the "banks" of same are now under water.
#7275
New Member
Looks like my rain dance worked.
It appears that El Nino may actually be taking shape here in NorCal.
End of drought? Won't know until snowpack is measured later this spring. But from the looks of the reservoirs viewed this past weekend, a good sign as much of the dried vegetation that has been on the "banks" of same are now under water.
End of drought? Won't know until snowpack is measured later this spring. But from the looks of the reservoirs viewed this past weekend, a good sign as much of the dried vegetation that has been on the "banks" of same are now under water.
#7277
Registered User
1000hp!?
On a 350z block? ... Ive been trying to break 700hp with my 20g greddy twin turbo kit without blowing the motor ... Any advice ? ... Im running manley rods and mahle pistons along with l19's studs ... Ported heads as well along with a more than capable fuel system and haltech standalone ecu ... People say i should run a darton sleeved block ... But here were i live (beirut lebanon ) ... There are no CNC machines here to use ... Last time i install darton sleeves they "sunk"
On a 350z block? ... Ive been trying to break 700hp with my 20g greddy twin turbo kit without blowing the motor ... Any advice ? ... Im running manley rods and mahle pistons along with l19's studs ... Ported heads as well along with a more than capable fuel system and haltech standalone ecu ... People say i should run a darton sleeved block ... But here were i live (beirut lebanon ) ... There are no CNC machines here to use ... Last time i install darton sleeves they "sunk"
#7280
New Member
iTrader: (1)
1000hp!?
On a 350z block? ... Ive been trying to break 700hp with my 20g greddy twin turbo kit without blowing the motor ... Any advice ? ... Im running manley rods and mahle pistons along with l19's studs ... Ported heads as well along with a more than capable fuel system and haltech standalone ecu ... People say i should run a darton sleeved block ... But here were i live (beirut lebanon ) ... There are no CNC machines here to use ... Last time i install darton sleeves they "sunk"
On a 350z block? ... Ive been trying to break 700hp with my 20g greddy twin turbo kit without blowing the motor ... Any advice ? ... Im running manley rods and mahle pistons along with l19's studs ... Ported heads as well along with a more than capable fuel system and haltech standalone ecu ... People say i should run a darton sleeved block ... But here were i live (beirut lebanon ) ... There are no CNC machines here to use ... Last time i install darton sleeves they "sunk"
BC or carillo rods, CP or wiseco pistons, there is a company doing closed deck blocks in the states now, that or sleeves, fuel is going to be the bigger issue, need a dual or triple pump made, the greddy kit i think the turbos are only good for 900hp. L19s are good, ported heads are good, id run cams, personally lookign at tomei 280 exhaust and intake for 8000rpm.
im only starting the build. Players like MM08 are 900whp and right there at it.