WTF .. ABS Code C1109?
#1
Banned
Thread Starter
iTrader: (1)
Join Date: Apr 2003
Location: NoVA
Posts: 7,920
Likes: 0
Received 0 Likes
on
0 Posts
WTF .. ABS Code C1109?
Just changed out my rotors and pads up front, ... and now my car wont rev past 1000 RPM's unless I clear the code.... I see an ABS code of:
C1109
This is really urking the **** out of me... I can drive the car for about 30 seconds .. stop pull over .. clear the code, then restart the car .. drive for 30 seconds... wash rinse repeat. I am beginning to hate my Z.
EDIT: Also.. the ABS BRAKE VDC and SLIP lights are on.
C1109
This is really urking the **** out of me... I can drive the car for about 30 seconds .. stop pull over .. clear the code, then restart the car .. drive for 30 seconds... wash rinse repeat. I am beginning to hate my Z.
EDIT: Also.. the ABS BRAKE VDC and SLIP lights are on.
Last edited by mdracer76; 05-04-2006 at 09:37 PM.
#3
Registered User
iTrader: (7)
Join Date: Mar 2004
Location: MD
Posts: 193
Likes: 0
Received 0 Likes
on
0 Posts
Is the brake fluid full? I had the ABS, VDC, Slip light when I first did my BBK. I filled the brake fluid, but it sucked it up and wanted more. Added more, lights went off. But if you didn't remove the caliper, I guess you shouldn't have that problem.
#5
Registered User
iTrader: (4)
Join Date: Mar 2005
Location: EveryWhere & yet... NoWhere
Posts: 2,880
Likes: 0
Received 3 Likes
on
3 Posts
See, this is why you should stick to working on your beater man... Leave the Z to the guys with the computers & the $80 labor charge...
J/K.. I hope you get this resolved man. You call Gene or Noah to ask?
J/K.. I hope you get this resolved man. You call Gene or Noah to ask?
#6
Banned
Thread Starter
iTrader: (1)
Join Date: Apr 2003
Location: NoVA
Posts: 7,920
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by yacoub
Did you connect EVERYTHING back up after changing the rotors and pads??
Originally Posted by turbogsr10
Is the brake fluid full? I had the ABS, VDC, Slip light when I first did my BBK. I filled the brake fluid, but it sucked it up and wanted more. Added more, lights went off. But if you didn't remove the caliper, I guess you shouldn't have that problem.
Originally Posted by spacemn_spiff
Did you knock off one of the ABS-TCS-VDC wheel speed sensors, that might do it? May be you accidentally did something to them, check their connections etc ?
Originally Posted by BamBam
See, this is why you should stick to working on your beater man... Leave the Z to the guys with the computers & the $80 labor charge...
J/K.. I hope you get this resolved man. You call Gene or Noah to ask?
J/K.. I hope you get this resolved man. You call Gene or Noah to ask?
On the way to the dealership, I had to clear it 3 times.. I live about 3 ~ 4 miles from dealer. We hooked up the Consult II to my car and started to drive it around.... and.. NADA.. NOTHING.. ZIP... it would not re-throw the damn code. Drove it for about 15 minutes with moderate to heavy braking. Still nothing. Which worries me even more..
When is this monster going to rear its ugly head again.....
Does anyone know or have a link to all the engine / abs / body Codes?
#7
Registered User
iTrader: (4)
Join Date: Mar 2005
Location: EveryWhere & yet... NoWhere
Posts: 2,880
Likes: 0
Received 3 Likes
on
3 Posts
C1109 Speed Control Actuator Assembly Cable Release Failure
At least that is what the Net says the OBD-II codes means.
Try this
http://www.dodgetrucks.org/docs/OBD-II%20Codes.pdf
(Yes I know it says Dodge... but I validated it with 4 other sites....)
or this
http://www.autoelectric.ru/diagnosti...ool/ccodes.txt
At least that is what the Net says the OBD-II codes means.
Try this
http://www.dodgetrucks.org/docs/OBD-II%20Codes.pdf
(Yes I know it says Dodge... but I validated it with 4 other sites....)
or this
http://www.autoelectric.ru/diagnosti...ool/ccodes.txt
Thread
Thread Starter
Forum
Replies
Last Post
Colombo
Forced Induction
35
11-09-2020 10:27 AM