Sound Performance hits 1017rwhp!!
#121
New Member
iTrader: (5)
![Default](https://my350z.com/forum/images/icons/icon1.gif)
Originally Posted by IntenseAero
Not trying to start anything brash in here but isn't this SP's 1000+HP thread, why all the {Nameless Shop} and or off topic talk about "dyno sweet spots" and such, this is simply put a grand accomplishment on SP's part! Enjoy and again congrats guy"Z"
"DON'T HATE, CONGRATULATE"
Mod for clean up in this thread and back to topic of SP 's accomplishment.
"DON'T HATE, CONGRATULATE"
Mod for clean up in this thread and back to topic of SP 's accomplishment.
#123
New Member
iTrader: (13)
![Default](https://my350z.com/forum/images/icons/icon1.gif)
Originally Posted by XKR
WOOOW ....hold up..Jorge, Eric and the AZ gang knows better than to think that I would be knocking anything that SP has done. That shop lets their work speak for itself...I was just responding to a question that someone asked about why more shops dont build 1000whp cars.
In my response I was trying to say that 1000 is wayyyyyy too much for me and I would not be able to use it...thought about it once...just once
Eric and Jorge...you know better than that.![Smilie](https://my350z.com/forum/images/smilies/smile.gif)
In my response I was trying to say that 1000 is wayyyyyy too much for me and I would not be able to use it...thought about it once...just once
![Smilie](https://my350z.com/forum/images/smilies/smile.gif)
![Smilie](https://my350z.com/forum/images/smilies/smile.gif)
![Smilie](https://my350z.com/forum/images/smilies/smile.gif)
You dont have to run 1000 all the time.. and with the rpm pushed like SP has there is plenty of powerband to enjoy
#124
Phenom
![](https://my350z.com/forum/images/ranks/premier.gif)
iTrader: (17)
Join Date: Aug 2005
Location: Greenville SC
Posts: 8,639
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://my350z.com/forum/images/icons/icon1.gif)
Originally Posted by IIQuickSilverII
its not for everybody, its all good, i wouldnt taken anything you said the wrong way
... like larry said... the vq will eventually be there... if you think about it mike...first it was 550 is all you need.. sleeves are needed for 600..now 700-800 is going to get common...eventually 1000whp will be there too... its just part of the developing...
You dont have to run 1000 all the time.. and with the rpm pushed like SP has there is plenty of powerband to enjoy
![Smilie](https://my350z.com/forum/images/smilies/smile.gif)
You dont have to run 1000 all the time.. and with the rpm pushed like SP has there is plenty of powerband to enjoy
#126
New Member
iTrader: (5)
![Default](https://my350z.com/forum/images/icons/icon1.gif)
Chris.. i don't know if it was mentioned already.. but is this motor sleeved or non-sleeved? because alot of the motors that were having coolant problems were sleeved.. and i believe the Injected car isn't sleeved? so maybe sleeves might be a minor cause of the coolant problems?
edit: read the shop update thread.. it has sleeves.. err.. nevermind
edit: read the shop update thread.. it has sleeves.. err.. nevermind
Last edited by doug; 09-13-2008 at 05:03 AM.
#127
Banned
iTrader: (21)
Join Date: Dec 2003
Location: Florida
Posts: 4,472
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://my350z.com/forum/images/icons/icon1.gif)
Originally Posted by phunk
if there is any problem with the stock manifold that is related to the slope in the roof, it would only be if the plenum roof is shrouding the front cylinders. however, as far as i have seen, it is all speculation anyway. but either way, our intake has plenty of clearance over the runner inlets not to shroud them.
#128
Registered User
iTrader: (1)
Join Date: Sep 2007
Location: Texas, Arizona,Cayman Island
Posts: 5,256
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://my350z.com/forum/images/icons/icon1.gif)
Originally Posted by IIQuickSilverII
its not for everybody, its all good, i wouldnt taken anything you said the wrong way
... like larry said... the vq will eventually be there... if you think about it mike...first it was 550 is all you need.. sleeves are needed for 600..now 700-800 is going to get common...eventually 1000whp will be there too... its just part of the developing...
You dont have to run 1000 all the time.. and with the rpm pushed like SP has there is plenty of powerband to enjoy
![Smilie](https://my350z.com/forum/images/smilies/smile.gif)
You dont have to run 1000 all the time.. and with the rpm pushed like SP has there is plenty of powerband to enjoy
![](https://my350z.com/forum/images/smilies/icon27.gif)
Sorry for OT ...
Jorge .... because of the hurricane, change of plans...catch up with the gang later in the month.
![Frown](https://my350z.com/forum/images/smilies/frown.gif)
#129
Registered User
iTrader: (6)
![Default](https://my350z.com/forum/images/icons/icon1.gif)
Originally Posted by doug
Chris.. i don't know if it was mentioned already.. but is this motor sleeved or non-sleeved? because alot of the motors that were having coolant problems were sleeved.. and i believe the Injected car isn't sleeved? so maybe sleeves might be a minor cause of the coolant problems?
edit: read the shop update thread.. it has sleeves.. err.. nevermind
edit: read the shop update thread.. it has sleeves.. err.. nevermind
#130
Sponsor
Injected Performance
Injected Performance
iTrader: (15)
Join Date: Jun 2004
Location: Houston
Posts: 636
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://my350z.com/forum/images/icons/icon1.gif)
The drag Z does have Darton sleeves as well as Wongy's G35 and countless other sleeved VQs we have built and are running around on the streets currently. No coolant issues with any of the cars to date (crosses fingers).
#131
CJ Motorsports
iTrader: (21)
![Default](https://my350z.com/forum/images/icons/icon1.gif)
who still has coolant system issues that didnt use stock DE gaskets or a weak 65lb ft on the headstuds or something? i was one of the first guys but it was just a bad sleeve job and/or not enough headstud torque.
sleeves vs not sleeved doesnt dictate much. just cause one guy has properly installed sleeves with no issues, doesnt mean the guy with crappy done sleeves wont have issues.
sleeves just leave more room from error is all, but done right it will be fine. in my case it was not. for some they dont have enough torque on the studs, for some they didnt prep the surfaces well enough before assembled, for some they had too much timing and blew out a gasket...
basically all im saying is that we have plenty of VQs out and about with no cooling system issues so i think that the big mystery on how to seal the heads is over.... there are no secrets just some people doing it right and some people doing it wrong. i did mine wrong first. but the last 2.5+ years its been bullet proof thru endless abuse. i havent bled my coolant system or touched anything related for over 2 years. crap i dont even pay attention anymore its been so solid... thats how they should all be.
use a good gasket, use a good amount of torque on the studs, dont run sleeves if they were not put in correctly, and dont tune too aggressively tryign to break 1200rwhp with pump gas just cause you have meth or some other bandaid.
sleeves vs not sleeved doesnt dictate much. just cause one guy has properly installed sleeves with no issues, doesnt mean the guy with crappy done sleeves wont have issues.
sleeves just leave more room from error is all, but done right it will be fine. in my case it was not. for some they dont have enough torque on the studs, for some they didnt prep the surfaces well enough before assembled, for some they had too much timing and blew out a gasket...
basically all im saying is that we have plenty of VQs out and about with no cooling system issues so i think that the big mystery on how to seal the heads is over.... there are no secrets just some people doing it right and some people doing it wrong. i did mine wrong first. but the last 2.5+ years its been bullet proof thru endless abuse. i havent bled my coolant system or touched anything related for over 2 years. crap i dont even pay attention anymore its been so solid... thats how they should all be.
use a good gasket, use a good amount of torque on the studs, dont run sleeves if they were not put in correctly, and dont tune too aggressively tryign to break 1200rwhp with pump gas just cause you have meth or some other bandaid.
#133
Z + Rear Seat
![](https://my350z.com/forum/images/ranks/premier.gif)
iTrader: (3)
Join Date: Jun 2005
Location: St.Pete,FL
Posts: 1,642
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://my350z.com/forum/images/icons/icon1.gif)
Originally Posted by phunk
use a good gasket, use a good amount of torque on the studs, dont run sleeves if they were not put in correctly, and dont tune too aggressively tryign to break 1200rwhp with pump gas just cause you have meth or some other bandaid.
I read through this thread again and it seems like you (phunk) are the designer of the intake used on the SP 1017whp car. Congratulations... job well done. It is very difficult to design something like an intake manifold from scratch, manufacture it, and get it to work better than an OEM original product. Kudos on everything working out and it holding together for all that horsepower.
Also congratulations to the Sound Performance people for dedicating their funds and time to create a project like this. Quite an accomplishment. Interesting that all three shops to reach 1000whp have done so on their own nickel with a shop car. Very cool!
I have been curious about one thing, however. Why Sound Performance? I thought you were a stereo shop the first couple of times I saw your name. I'm sure I won't confuse your name any more, but it still seems an odd choice to me.
#134
Vendor - Former Vendor
iTrader: (208)
Join Date: Dec 2004
Location: Arizona
Posts: 2,038
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://my350z.com/forum/images/icons/icon1.gif)
Originally Posted by __jb
... Interesting that all three shops to reach 1000whp have done so on their own nickel with a shop car. Very cool!
I have been curious about one thing, however. Why Sound Performance? I thought you were a stereo shop the first couple of times I saw your name. I'm sure I won't confuse your name any more, but it still seems an odd choice to me.
I have been curious about one thing, however. Why Sound Performance? I thought you were a stereo shop the first couple of times I saw your name. I'm sure I won't confuse your name any more, but it still seems an odd choice to me.
![Wink](https://my350z.com/forum/images/smilies/wink.gif)
"What's in a name? That which we call a rose
By any other name would smell as sweet."
-Juliet
Darrren
#135
Sponsor
Sound Performance
Sound Performance
![Default](https://my350z.com/forum/images/icons/icon1.gif)
Originally Posted by __jb
I have been curious about one thing, however. Why Sound Performance? I thought you were a stereo shop the first couple of times I saw your name. I'm sure I won't confuse your name any more, but it still seems an odd choice to me.
Long story short.....
Back in 1988 I opened up as Sound F/X, primarily a stereo shop. In 1989 I bought a Supra turbo..... started modding it...... in 1991 I was making 570 RWHP which was UNHEARD of for 1991!!! I wanted to become a HKS and Greddy dealer but they said that our name was too much audio orientated so I changed it to something that had both audio and performance in the name. Hence Sound Performance. Since about 1995 we have been 100% performance. I think there is only 1 or 2 shops in the country that have been Greddy/HKS dealers longer than I have!!
#136
Z + Rear Seat
![](https://my350z.com/forum/images/ranks/premier.gif)
iTrader: (3)
Join Date: Jun 2005
Location: St.Pete,FL
Posts: 1,642
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://my350z.com/forum/images/icons/icon1.gif)
Originally Posted by INTENSEPOWER
This motor isn't any of the above mentioned shops "first rodeo" ![Wink](https://my350z.com/forum/images/smilies/wink.gif)
![Wink](https://my350z.com/forum/images/smilies/wink.gif)
I don't think it's the first high horsepower engine they have put together either.
Originally Posted by INTENSEPOWER
"What's in a name? That which we call a rose
By any other name would smell as sweet."
-Juliet
Darrren
By any other name would smell as sweet."
-Juliet
Darrren
You've been very helpful.
#137
Z + Rear Seat
![](https://my350z.com/forum/images/ranks/premier.gif)
iTrader: (3)
Join Date: Jun 2005
Location: St.Pete,FL
Posts: 1,642
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://my350z.com/forum/images/icons/icon1.gif)
Originally Posted by SoundPerformance
Long story short.....
Back in 1988 I opened up as Sound F/X, primarily a stereo shop. In 1989 I bought a Supra turbo..... started modding it...... in 1991 I was making 570 RWHP which was UNHEARD of for 1991!!! I wanted to become a HKS and Greddy dealer but they said that our name was too much audio orientated so I changed it to something that had both audio and performance in the name. Hence Sound Performance. Since about 1995 we have been 100% performance. I think there is only 1 or 2 shops in the country that have been Greddy/HKS dealers longer than I have!!
Back in 1988 I opened up as Sound F/X, primarily a stereo shop. In 1989 I bought a Supra turbo..... started modding it...... in 1991 I was making 570 RWHP which was UNHEARD of for 1991!!! I wanted to become a HKS and Greddy dealer but they said that our name was too much audio orientated so I changed it to something that had both audio and performance in the name. Hence Sound Performance. Since about 1995 we have been 100% performance. I think there is only 1 or 2 shops in the country that have been Greddy/HKS dealers longer than I have!!
Congratulations again on hitting the 1000whp mark with a VQ and good luck on future builds...
#139
Banned
iTrader: (44)
![Default](https://my350z.com/forum/images/icons/icon1.gif)
just wondering, but have you ever compared making the merge area a rounder edge as opposed to the 'knife'-y edge you have?
those collectors are beautiful btw
also, what about on the heads (same question for the porting)? is it common knowledge that the sharp edge is the best way to seperate the flow?
those collectors are beautiful btw
![](https://my350z.com/forum/images/smilies/icon21.gif)
also, what about on the heads (same question for the porting)? is it common knowledge that the sharp edge is the best way to seperate the flow?