FAQ: Official wheel "SPACER" thread!
#1361
350Z/370Z Tech Moderator
MY350Z.COM
MY350Z.COM
Attachment 452918
Attachment 1
Attachment 452916
Ordered H&R 15mm bolt on spacers all the way around.
19/9 et25. 245/35
19/10.5 et20 265/35
Lowered almost 2 inches now.
Shooting for a half inch lower all around.
Setting camber at -2.2 front -2.5 rear.
Fenders are rolled but not pulled or flat rolled.
Thought??? Yes, No?
Pics of similar???
Just in for some feedback and similar setups.
Thanks.
Attachment 1
Attachment 452916
Ordered H&R 15mm bolt on spacers all the way around.
19/9 et25. 245/35
19/10.5 et20 265/35
Lowered almost 2 inches now.
Shooting for a half inch lower all around.
Setting camber at -2.2 front -2.5 rear.
Fenders are rolled but not pulled or flat rolled.
Thought??? Yes, No?
Pics of similar???
Just in for some feedback and similar setups.
Thanks.
Your quoted specs (and pics?) are before or after spacers?
#1362
Registered User
Join Date: Aug 2016
Location: Pueblo West, Colorado
Posts: 439
Likes: 0
Received 31 Likes
on
27 Posts
The pictures I took are of my wheel set up without spacers. I just ordered them from concept Z today.
The wheel and tire specs however are my current set up.
#1363
I realize now that after I slipped on the spacers, the wheel hub rings (and now likely the wheels themselves) weren't fully flush with the hub face due to the spacers taking up 5mm of the hub ridge that the rings slide over and therefore not allowing the wheels to flush up and giving me a false torque reading.
#1364
350Z/370Z Tech Moderator
MY350Z.COM
MY350Z.COM
Attachment 452918
Attachment 1
Attachment 452916
Ordered H&R 15mm bolt on spacers all the way around.
19/9 et25. 245/35
19/10.5 et20 265/35
Lowered almost 2 inches now.
Shooting for a half inch lower all around.
Setting camber at -2.2 front -2.5 rear.
Fenders are rolled but not pulled or flat rolled.
Thought??? Yes, No?
Pics of similar???
Just in for some feedback and similar setups.
Thanks.
Attachment 1
Attachment 452916
Ordered H&R 15mm bolt on spacers all the way around.
19/9 et25. 245/35
19/10.5 et20 265/35
Lowered almost 2 inches now.
Shooting for a half inch lower all around.
Setting camber at -2.2 front -2.5 rear.
Fenders are rolled but not pulled or flat rolled.
Thought??? Yes, No?
Pics of similar???
Just in for some feedback and similar setups.
Thanks.
Personally think it looks fine but your choice.
#1365
350Z/370Z Tech Moderator
MY350Z.COM
MY350Z.COM
#1366
Registered User
Join Date: Aug 2016
Location: Pueblo West, Colorado
Posts: 439
Likes: 0
Received 31 Likes
on
27 Posts
No garuntees I'm going lower. Hoping to see some similar setups. May need to roll fenders a little more. My next set of wheels and tires will be less function and more fashion. Lol. These are my track wheels/tires.
#1367
350Z/370Z Tech Moderator
MY350Z.COM
MY350Z.COM
EDIT: Site has been condemned by MacAfee. User banned.
Last edited by MicVelo; 01-26-2019 at 07:17 AM.
The following users liked this post:
reyfx (09-23-2020)
Thread
Thread Starter
Forum
Replies
Last Post
2003, 25, 30, 30mm, 350z, 522, affect, alignment, apacers, bore, camber, car, centric, correctly, cut, dallas, diego, faq, g35, hub, hubcentric, ichiba, install, installing, laigment, mm, negative, nissan, protrusion, removes, rings, san, size, spacer, spacers, specs, studs, texas, thread, unnecessary, wheel, wheelspacer, wobble, xxr