HELP! did I install my sikky raised subframe bushings wrong?
#1
HELP! did I install my sikky raised subframe bushings wrong?
I had my subframe out for a lot of stuff to be replaced so I thought it was a good time to get solid sub frame mounts. I got raised mounts from sikky. I installed them based off of how the stocks ones seemed. The rear 2 most mounts have the raised part closer to the ground, and the front 2 the raised side is up. I did this because the stock rubber bushings were more raised on the front side up, and the rear most were raised to the ground. Installing the subframe was a nightmare, because it did not slide in the 4 pins, it took me having to use a jack, dead blow hammer and then finally get it close to the threads i had to use am impact gun to slowly get all sides to move. It is so wedged on there it did not even needs nuts to stay in place. After looking online I see it seems people have installed all 4 with the thicker part facing DOWN. IS that right? did i do mine wrong? if so this is going to be a nightmare to take out now since its so wedged in. I figured if all 4 are facing down nothing is being raised? please help ASAP!!!
#2
Super Moderator
MY350Z.COM
MY350Z.COM
iTrader: (8)
Yup, you installed them wrong, the thinner goes up, raising the subframe to the body
The following users liked this post:
etkms (07-23-2015)
#4
Beofre I even saw this thread I was driving before (not the z of course ) and realized raised means raised higher like terrasmak said to the bodyl I am sooo stupid. I wish I would have realized this earlier. Its 4am and I can't sleep I am having nightmares how the hell I am going to get this thing out!!!!!!!!!!! I can't believe this. My worst case is I am thinking of me having to cut my subframe out and buying a new one
If a miricle happens and it comes out whole my next issue is how do i take the pressed in bushings out since they have a flange on both ends i cant just push one out threw the other side....... oh boy....
If a miricle happens and it comes out whole my next issue is how do i take the pressed in bushings out since they have a flange on both ends i cant just push one out threw the other side....... oh boy....
Last edited by etkms; 07-23-2015 at 12:14 AM.
The following users liked this post:
etkms (07-23-2015)
#7
New Member
iTrader: (15)
When i was swapping around pumpkins i briefly attempted to transplant the SPL solid differential ear bushings from one of my diffs to the other...quickly realized it wasnt worth it because i would have to damage the bushings. Thought i would chime in since they install the same way the subframe bushings do. I think if you fabbed the right tool to sit on the inner lip of a bushing half combined with an air hammer might do the trick.
There is a used set for sale in the classifieds where the ear bushings seem to have been removed, but they do look damaged to some degree but still usable. Again not subframe bushings but relevant into if you can actually get the subframe out. Good luck!
There is a used set for sale in the classifieds where the ear bushings seem to have been removed, but they do look damaged to some degree but still usable. Again not subframe bushings but relevant into if you can actually get the subframe out. Good luck!
Trending Topics
#9
New Member
iTrader: (6)
Make friends with a tech at a Nissan dealership. When we have a 350Z come in that needs a rear diff bushing, we replace the whole subframe. Nissan doesn't make a replacement bushing. I've brought at least a dozen perfectly good (with leaking rear bushing) subframes to the recycler over the last 4 years. If you can get someone to give or sell you a used one, all you'll have to do is replace the bushing with a Whiteline (or SPL) one.
I just hope you didn't bend or crack any of the 4 studs from the chassis. You'll be looking at a huge bill or a new car to fix those.
I just hope you didn't bend or crack any of the 4 studs from the chassis. You'll be looking at a huge bill or a new car to fix those.
#11
Oh to update this! Thankfully it wasn't as bad as I thought. The sub frame came out quite easy with a pry bar evenly at all 4 corners. The hardest part was taking the bushings out again! I was actually able to get them out with a slide hammer and an strange attachment that came with a kit I rented to remove bearings. I am very thankful I did not need to buy anything new or have to cut anything. The sub frame and car is back together and all is well. A stupid mistake that cost me a lot of time and aggravation.
Last edited by etkms; 08-03-2015 at 12:03 AM.
#13
Last edited by etkms; 08-03-2015 at 10:33 AM.
Thread
Thread Starter
Forum
Replies
Last Post
Lt_Ballzacki
Brakes & Suspension
39
08-06-2021 06:19 AM