hey im new here im from chihuahua mexico i have some mods on my z but i want more, i have injen intake,headers invidia exhaust, act clutch, reflash ecu and crankshaft pulley, it really runs good but what else i can put on it?

 

ur posting this in the wrong section and dont go posting this at all..use the search button and read thru many many threads that have covered dumb *** questions like this time and time again before u think of posting again.

there are many many many other things you can do, figure out how deep ur pockets are

 

2003 Nissan 350Z Touring, 6 speed, Completely Stock Motor, Vortech SC, ET Streets

Night of March 29, 2012

R/T........ .068
60'....... 1.704
1/8....... 7.533
MPH...... 96.38
1/4...... 11.647
MPH.... 120.48

Please put me back to the Top of the List

Thanks,

TimRod

 

very nice man...congrats...now i just wish i had the z still to drop the pulley to the 2.87 and go harder with a little more power

 

Updates this evening. Sorry for the delay.

 

Updated Top 25 Nitrous List:

Added:
8. denchan350gt --------05 G35- Auto 125 shot 12.357@114.30mph 2.027 60ft Slicks
11. tuckerst85 ---------05 Tour Auto _75 shot 12.782@108.03mph 1.993 60ft DR's

Updated Top 25 Supercharged List:

1. OldManZ350 --------------03 Tour 6spd ----Vortech 11.647@120.48mph 1.704 60ft Verified Slicks

 

My Tires are ET STREETS........

Thanks

TimRod

 

Edited.....

 

Took my car to the dyno today with the direct port setup. Made 396/441 with bottle psi @ 950. 410/470 @1100

 

Nice!! Do you have a pic of your dyno sheet. When are you going to hit the track with your new set-up?

 

Thats some axle breaking torque.

 

Mike can you update my listing? I'm down to a 11.7 now the slip should be in my latest PB thread. I don't think the position has to change.

 

 

Went to my local 1/8th mile track and made some test runs. Unpreped track I ran a 7.43@95 on rev limiter the last 40 foot. 1.68 was my best 60' of the night after playing with the coil overs. But it was spinning to bad to really be ableto tell what was goin on. I'm ready to take it to coastal and run 1/4 next Friday.

 

Damn I wish our track was open... still closed for another month

 

Hmm 1.68 60ft and you were spinning? Doesn't sound right.

 

i was getting 1.61-1.63 range before with the old setup.
its spinning the tires bad in first now, but that track wasnt prepped either. im looking for some 1.55-1.57 60s when i get on a good track.

 

I hit 1.510 slightly spinning and at about 1/2 throttle for the first 20ft. It's possible.

 

Results in about3 hours. I'm pretty excited to see what the car will do. I took out the factory tools. And heavy carpet in the hatch and a bunch of little parts and brackets not needed on the car.

 

First pass and best pass of the night. pass after this i had a 1.60 60' but the car fell off up top. bottle psi was getting low. i only get 2 runs per bottle. then switched bottles and for some reason the other bottle dont hit hard. made 30 less ft/lbs on this bottle on the dyno. and i tried running with it and it sucked so i loaded up the car and went to logans for a late dinner to celebrate my hundredth i picked up.


im pretty confident if i can get my 60' down with a full bottle then the car would be in the 11.1x range. it was still spinning pretty good on this run and the car bounces real bad i need new suspension based around drag racing.