CaligrownZ

iTrader: (1)

Visited Specialty Z today in SoCal, to get the UpRev Osiris tune.
First off, the guys who work there, especialy Sebastian are great guys. Very friendly and helped me understand a lot more about the HR. I highly recommended their work for anything… they really know everything there is to know about any Z

We did 8 runs on the dyno.

Before tuned I was at: Max Power 289.58/ Max Torque 251.14

After the reflash with the Osiris, We were able to squeez out around 4-5 whp
.
After tune I was at: Max Power 293.68/ Max Torque 253 around 4.7k rpms

Also fixed the cel and raised my redline to 8.2k rpms


Here are some of my mods:

Injen dual CAI
AAM test and y pipe
Greddy Single


Youtube link:
http://www.youtube.com/watch?v=RoHXdajMsyI



**** was loud .
Shot with my iphone...

Mad props to SZ
http://www.specialtyz.com/

ZSilverBullet28

It sounds great man

DavesZ#3

iTrader: (26)

All you could get is 5 hp with a tune?????

CaligrownZ

iTrader: (1)

Sadly yes... I was told my HR was running pretty good (a little lean) before the tune.
Adjusted the fuel and air
DE's have greater numbers with a tune 15-20+ or so whp.
Some HR's gain between 5-12 whp
I could run w/ octane booster but that has little gains with NA builds

WTFMike

iTrader: (2)

Isn't 8,200 rpms kinda high for stock valve springs?

davidv

iTrader: (2)

So the net gain is a 1.4 percent increase in peak horsepower? With respect this is hardly "Oh Boy!"

CaligrownZ

iTrader: (1)

Yeah, 8,200 is high, but its like saying there is no rev limiter... until 8.2k... i doubt this car will ever see pass 8 if that

Voboy

iTrader: (58)

dyno sheet?

8.2k sounds like the average .4-.6 rpm bump most people do...

Duckeee

iTrader: (7)

i was expecting better results after the tune and worse numbers before the tune.

lgear080

iTrader: (21)

huh... i'd say quit while you're "ahead" - absolutely no on headers.

post the dyno sheet before and after.

0jiggy0

iTrader: (13)

8200 is a bit too high. I wouldn't go over 7750 max on stock erything.

CaligrownZ

iTrader: (1)

Dyno sheet posted.

Duckeee

iTrader: (7)

yeah with that curve 8.2k redline is almost pointless

Mr. Nibiru

I think you should have just gone with 8,000 since this is only 500 rpm above the factory redline. Of course I did go with 7,200 rpm on my 03' with no problem so you should be okay.

I think your numbers are good for just 3 bolt ons and a tune. You really didn't change that much from the OEM setup which is why you didn't see that much on the tune. Cams would have put your over 300whp and that is probably the best thing you can do N/A. I think a lot of people expect to much N/A from our cars in terms of performance over OEM standards. The best I have seen on a DE is 277whp, so you making 20 more makes sense.

Just goes to show you, if you are going to try for over 300whp you have to accept the fact that FI is the only way to get there or extreme N/A mods like a head build or cams. Or nitrous if you want to go the cheap way. Simple bolt ons won't generally get you there.

Also, don't get a tune unless you severly alter the car such as forced induction or a complete head build. As you can see, the oem cpu is totally capable of handling bolt ons.

dcastillo819

iTrader: (2)

^+1 agreed. I think you should have done better but what octane gas were you using? jw

Mr. Nibiru

By the way, your dyno is nice and smooth. But as you can see, raising your redline really didn't benefit the car any. It peaks out at about 6700 rpm. So raising the redline to over 8,000 rpm doesn't increase the power just the possible shifting point. The good thing is that when you shift at the new redline it should put you close to the optimum hp level on the rpm drop. This will help in drag racing with cars with shorter gear ratio's like WRX and the like. Raising the redline would be more beneficial for a higher final ratio that shorten the gears at the trade off of acceleration.

I am sacrificing top speed for overall acceleration with the 4.083 final drive.

Overall I would be happy with the outcome of your car. I don't think the tune was necessary though with so few modification.

By the way, don't go headers on the HR motor. The price for the consistent 5hp gain throughout the powerband isn't worth it.

There are other way of increasing speed without increasing horsepower.

bbs350z

iTrader: (85)

car sounds great, and impressive power for minimal bolt ons. i say keep it as it is and enjoy it

KingBaby

iTrader: (3)

Nice...

Hopefully your driving doesn't allow you to break your car! I set my tach to 7400rpm. I shift within in the next second when pushing it. So around 7500-7800rpm is ideal.

CaligrownZ

iTrader: (1)

Since my car is the base model, What are your guys' thoughts on finding a used LSD diff and picking up 4.08 gears and swapping that in??

Alberto

iTrader: (14)

Terrible advice.