nismored

3M 90 is thicker than horse semen, you think its gonna go through the backing of the material.

I have found that if you spray it, let it bubble and set for a couple of minutes and then press the material to the surface, it doesn't seep through and provides a nice strong hold.

somebody

iTrader: (11)

you have to dry up the super77 for a bit before you apply the fabric.
Don't apply the fabric when the glue is wet......when it starts to dry, apply the fabric.

Jun

iTrader: (45)

how many yards are you guys buying to do the whole center console?

Resolute

iTrader: (2)

Wow. Definitely going to try this on some interior pieces. Thanks Somebody for the pics and how-to guide!

Will

Soni

1 yard should be enough!!

pearlwhite_z

iTrader: (14)

i need two yards, anymore somebodY?

eXe-Chris

iTrader: (-2)

It took me close to 4 yards to do both a-pillars, center console, shifter console, center console in my car. So I seriously doubt he will be able to do the entire center console with 1 yard.

CJSBOSOX

iTrader: (5)

Well it's not like the interior materials on the Z are top notch to begin with. And yes, I have seen this in person and it looks good. looks low key and not over done.

Get_Zwole

iTrader: (34)

Its the brickyard rat take what he says with a grain of salt hes a bitter old man.

*ICE*

iTrader: (48)

well I had it with my center console. Most of the edges are not sticking anymore and had wrinkled up, also it made my cubby door hard to open or close. I decided to remove everything and leave the cubby door fabric there. Looks decent anyways.

Here are some pics of the cubby door part that people been having problems with and pics of the center dash without the fabric.

Duskywing

iTrader: (1)

How do I remove the connection? I've been struggling for 15mins, though I am not really forcing it as I don't want to break it.

*ICE*

iTrader: (48)

Is that underneath the 3 gauges pod? There is a notch on the other side of the connector, just press it down and pull it out.

Duskywing

iTrader: (1)

Yes, it is the hazard button connector underneath the parking brake.

Spork

iTrader: (6)

I believe that's under the console by the parking brake, etc. There's a tab on either side. Push the tab in and pull.

Duskywing

iTrader: (1)

I already asked a friend and he can't find a tab either. It seems that the connection is split into 3...

Duskywing

iTrader: (1)

Wohooo... just finished the shifter console.



Btw, I still can't figure out on removing the center console connector. Any help would be appreciated.

Anthony C

iTrader: (1)

needle nose pliars and just grab it and pull lightly. it will come off easily... i tried by fingers and after 10 seconds i was like "light bulb" and just used needle nose pliars and no problem.


on another note. i wrapped mine yesterday... well so far just the top half and the cubby door... i ****ed it up bad. luckily i have xtra so im gonna redo it on the next nice day... its a pain in the *** to do and im a VERY DIY kinda guy. oh well i know what not to do next time.


Greg, do you have anymore of this ready for shipping or did you run out?

Get_Zwole

iTrader: (34)

thats what im afraid of im mostly DIY as well but ive never wrapped anythign like this.

Duskywing

iTrader: (1)

Here's the installed pictures. I decided not to do the center console for now to gauge how the material fare during the summer.

Gibbs

iTrader: (6)

God I would love to do this but I just bought a real CF shifter cover for my 08, and the contrast of the two different styles would look weird.