Official STS Rear Mount Turbo Discussion Thread
#2661
Registered User
Join Date: Dec 2010
Location: saltlakecity ut
Posts: 93
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://my350z.com/forum/images/icons/icon1.gif)
how did you get a lack of oil? even if the pump failed, the turbo would overflow with oil but woudnt be enough to drain your motor of oil. And if the seal on the turbo actually went, your car woulda been smoking like a forest fire well before your oil pressure went low enough to kill the engine.
anyone that has to use a oil sump pump is absolutely crazy not to have an oil pressure gauge.
anyone that has to use a oil sump pump is absolutely crazy not to have an oil pressure gauge.
That tells me he just don't honor warranties.
#2663
Registered User
Join Date: Dec 2010
Location: saltlakecity ut
Posts: 93
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://my350z.com/forum/images/icons/icon1.gif)
The engine wasn't a complete loss, I learned from my first build to shut it down right away.
The bearings were in pretty bad shape but not spun.
They could have saved the crank but I got that replaced just so I don't have it to worry about.
The heads and cylinders were a little scraped up from the trash in the oil but were conditioned just fine.
BTW started out with a gt35 and it blew a seal. My tuner then got a precision 6562 and he then blew out that seal too, this time the alarm went off for the oil pump. This is when my tuner figure out what was the cause of the turbo failers. I guess the pump was failing for a while but not enough to trip the 1 psi alarm.
So any way I had the seal repressed, then I got an exa pump put on took the car that night with a conservative 8lb boost tune and not long after that I felt a grinding sensation when I gave it throttle in 4th, first thing I did was look at my oil pressure and it was good till I took my foot off the gas.
At idol it didn't have hardly any pressure at all.
The bearings were in pretty bad shape but not spun.
They could have saved the crank but I got that replaced just so I don't have it to worry about.
The heads and cylinders were a little scraped up from the trash in the oil but were conditioned just fine.
BTW started out with a gt35 and it blew a seal. My tuner then got a precision 6562 and he then blew out that seal too, this time the alarm went off for the oil pump. This is when my tuner figure out what was the cause of the turbo failers. I guess the pump was failing for a while but not enough to trip the 1 psi alarm.
So any way I had the seal repressed, then I got an exa pump put on took the car that night with a conservative 8lb boost tune and not long after that I felt a grinding sensation when I gave it throttle in 4th, first thing I did was look at my oil pressure and it was good till I took my foot off the gas.
At idol it didn't have hardly any pressure at all.
#2665
New Member
iTrader: (1)
Join Date: Jun 2008
Location: wichita,ks
Posts: 341
Likes: 0
Received 0 Likes
on
0 Posts
![Unhappy](https://my350z.com/forum/images/icons/icon9.gif)
I had an ipp engine on a sts kit and my engine failed due to lack of oil this is after replacing the p.o.s Chinese built pump with a example pump. I saw the pump working when it was tested with my own eyes.
My engine went the same day I picked it up.
Kyle did not warranty the engine nor did he refund my core charge from my original engine.
Don't expect your $ back if if engine goes bang.
Good luck with your build, I'm going with the momentum kit now.
My engine went the same day I picked it up.
Kyle did not warranty the engine nor did he refund my core charge from my original engine.
Don't expect your $ back if if engine goes bang.
Good luck with your build, I'm going with the momentum kit now.
#2667
New Member
iTrader: (1)
Join Date: Jun 2008
Location: wichita,ks
Posts: 341
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://my350z.com/forum/images/icons/icon1.gif)
Oh just to give you you a heads up this was the day after i got it back so definitely was getting use to the setup it was my 60 ft i need to work on but need to get a launch control setup on it but not sure if it will work on a base though i need it to build a little bit of boost at least to get off the the line faster and maybe some d/r's.
#2669
Registered User
iTrader: (19)
![Default](https://my350z.com/forum/images/icons/icon1.gif)
Oh just to give you you a heads up this was the day after i got it back so definitely was getting use to the setup it was my 60 ft i need to work on but need to get a launch control setup on it but not sure if it will work on a base though i need it to build a little bit of boost at least to get off the the line faster and maybe some d/r's.
str8dum1, I'm leaning towards a precision turbo, .76mm bb
The LQ9 is "only" 6.0l heh
#2671
New Member
iTrader: (11)
![Default](https://my350z.com/forum/images/icons/icon1.gif)
76 is too small (unless you mean 2). they use 76mm on 3 - 3.4L supras. even Snyper said that 88mm felt too small and had little lag.
You have a long road ahead in your build, but I'd seriously look at compressor maps. you'll be surprised how much turbo you can really and get a great powerband. 6L is a lot of displacement.
You have a long road ahead in your build, but I'd seriously look at compressor maps. you'll be surprised how much turbo you can really and get a great powerband. 6L is a lot of displacement.
#2672
Registered User
iTrader: (19)
![Default](https://my350z.com/forum/images/icons/icon1.gif)
76 is too small (unless you mean 2). they use 76mm on 3 - 3.4L supras. even Snyper said that 88mm felt too small and had little lag.
You have a long road ahead in your build, but I'd seriously look at compressor maps. you'll be surprised how much turbo you can really and get a great powerband. 6L is a lot of displacement.
You have a long road ahead in your build, but I'd seriously look at compressor maps. you'll be surprised how much turbo you can really and get a great powerband. 6L is a lot of displacement.
But the actual turbo part is going to be last, I didn't order anything turbo related yet. Just want to get the long block build and in our possession
[/threadjack sorry guys]
#2674
Registered User
iTrader: (1)
Join Date: Oct 2010
Location: Enid, OK
Posts: 104
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://my350z.com/forum/images/icons/icon1.gif)
Ok I'm about to start my build. My goal is 500whp with a rear mount. I'm trying to buy a block and crank from a member on here if he'll ever get me a shipping quote. Obviously forged bottom end is needed, but everywhere I look i get some mixed reviews on the DE heads. Would 500whp be alright with the stock DE heads? Also hoping you guys could help me out on which turbo to get. I'm knowledgeable in just about every aspect of building motors, but I've only had 2 other boosted cars one was a twin turbo VR4, had stock turbos. The other was a 300zx TT upgraded turbos but I didn't choose the turbos. So my question is can someone help me decide on a turbo to buy. Just seems like theres a million options out there. Thanks in advance.
#2678
Registered User
Join Date: Aug 2011
Location: Puerto Rico
Posts: 15
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://my350z.com/forum/images/icons/icon1.gif)
Hi,
I red that you have the sts manual on PDF. I bought a used sts kit that came without it.
Please send it to jsrodz@gmail.com
Thanks for your help
Jesus
I red that you have the sts manual on PDF. I bought a used sts kit that came without it.
Please send it to jsrodz@gmail.com
Thanks for your help
Jesus