Utec Map Sensor Calibration Off?
08-27-2007, 02:58 PM
#1
Registered User
Thread Starter
iTrader: (19)
Join Date: Feb 2005
Location: Indianapolis
Posts: 963
Likes: 0
Received 0 Likes
on
0 Posts
Utec Map Sensor Calibration Off?
For about 3 months I thought I had a severe boost leak because my utec would never show boost higher than 7.5 psi. Well after eliminating every boost leak my stupid a$$ looks at the dashboard on the UTEC with the car off... the map sensor is reading -1 psi just sitting in open air... so I guess I was hitting 8.5 psi the whole time.
Anyways I have the parameters set to Absolute and it reads -1 psi. when i have it set to Gauge it reads +19.4 psi... I dont know if my sensor is faulty or if it is supposed to be like this. I used the calibration card to calibrate it in the parameters, but im not sure if i should toy with it or get another map sensor.
Any input?
Anyways I have the parameters set to Absolute and it reads -1 psi. when i have it set to Gauge it reads +19.4 psi... I dont know if my sensor is faulty or if it is supposed to be like this. I used the calibration card to calibrate it in the parameters, but im not sure if i should toy with it or get another map sensor.
Any input?
08-27-2007, 07:00 PM
#7
Registered User
Thread Starter
iTrader: (19)
Join Date: Feb 2005
Location: Indianapolis
Posts: 963
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Z PHAT Z
You might also upgrade the software if you haven't done that.
it has the 2.8 software, and no I havent referenced it with a boost gauge. I just dont understand why it would read -1 psi with the car off
Trending Topics
08-27-2007, 07:31 PM
#11
Registered User
Thread Starter
iTrader: (19)
Join Date: Feb 2005
Location: Indianapolis
Posts: 963
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by jining
Yea yours isnt calibrated right or something, mine reads +.1 with the car off so I think mine is slightly off as well.
thanks for confirming, i will call turboxs tomorrow morning
08-28-2007, 05:47 AM
#13
Registered User
Thread Starter
iTrader: (19)
Join Date: Feb 2005
Location: Indianapolis
Posts: 963
Likes: 0
Received 0 Likes
on
0 Posts
soooo, I just called TurboXS and Jermaine said that -1psi sitting with the car off is normal, which I think is bs. Usually they are pretty good at helping me out but this time they had no interest. He told me to just play with the calibration numbers or something
03-24-2008, 06:21 AM
#14
New Member
iTrader: (4)
Join Date: Dec 2006
Location: ohio
Posts: 383
Likes: 0
Received 0 Likes
on
0 Posts
did you ever get this taken care of as I have the exact same problem. My txs map sensor is constantly reading -1 psi less than what it is supposed to be. I need it to be accurate as I took out my boost gauge and was planning on just using the map sensor to display my boost on my car pc screen.
03-26-2008, 01:57 PM
#15
My utec says +.4 (absolute) when the car is off. I have not calibrated the map sensor though.
Which brings me to my question:
How do you use the map sensor calibration card to enter the values into the utec? For example, my calibration card states:
PSI Output
Cal 1 input: 1176 Cal 1 output: 7.13
Cal 2 input: 1725 Cal 2 output: 20.18
BAR Pressure Output
Cal 1 input: 875 Cal 1 output: 0.00
Cal 2 input: 1485 Cal 2 output: 1.00
So my question is how do these figures translate into the between 1 and 300 values that the utec wants you to enter for map calibration? The only thing I could think of was for the PSI numbers to divide input by output, because both of those would result in numbers between 1-300... But this is just a guess.
Which brings me to my question:
How do you use the map sensor calibration card to enter the values into the utec? For example, my calibration card states:
PSI Output
Cal 1 input: 1176 Cal 1 output: 7.13
Cal 2 input: 1725 Cal 2 output: 20.18
BAR Pressure Output
Cal 1 input: 875 Cal 1 output: 0.00
Cal 2 input: 1485 Cal 2 output: 1.00
So my question is how do these figures translate into the between 1 and 300 values that the utec wants you to enter for map calibration? The only thing I could think of was for the PSI numbers to divide input by output, because both of those would result in numbers between 1-300... But this is just a guess.
Last edited by SpoilsofWar; 03-26-2008 at 02:08 PM.
03-26-2008, 02:45 PM
#16
I would also like to know, since my used MAP sensor didn't come with a card, and the settings on the UTEC are the default settings from the manual.
Intercept must be the value for 0 psi, and gradient is the rate by which the value will increase per a certain increase of boost - hmmm, yeah, not much information included to determine this. Hopefully someone knows.
Intercept must be the value for 0 psi, and gradient is the rate by which the value will increase per a certain increase of boost - hmmm, yeah, not much information included to determine this. Hopefully someone knows.
03-26-2008, 04:06 PM
#18
Registered User
iTrader: (2)
Join Date: Feb 2007
Location: Kansas
Posts: 101
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by SpoilsofWar
My utec says +.4 (absolute) when the car is off. I have not calibrated the map sensor though.
Which brings me to my question:
How do you use the map sensor calibration card to enter the values into the utec? For example, my calibration card states:
PSI Output
Cal 1 input: 1176 Cal 1 output: 7.13
Cal 2 input: 1725 Cal 2 output: 20.18
BAR Pressure Output
Cal 1 input: 875 Cal 1 output: 0.00
Cal 2 input: 1485 Cal 2 output: 1.00
So my question is how do these figures translate into the between 1 and 300 values that the utec wants you to enter for map calibration? The only thing I could think of was for the PSI numbers to divide input by output, because both of those would result in numbers between 1-300... But this is just a guess.
Which brings me to my question:
How do you use the map sensor calibration card to enter the values into the utec? For example, my calibration card states:
PSI Output
Cal 1 input: 1176 Cal 1 output: 7.13
Cal 2 input: 1725 Cal 2 output: 20.18
BAR Pressure Output
Cal 1 input: 875 Cal 1 output: 0.00
Cal 2 input: 1485 Cal 2 output: 1.00
So my question is how do these figures translate into the between 1 and 300 values that the utec wants you to enter for map calibration? The only thing I could think of was for the PSI numbers to divide input by output, because both of those would result in numbers between 1-300... But this is just a guess.
03-26-2008, 06:12 PM
#19
Banned
iTrader: (1)
Join Date: Feb 2004
Location: Dayton, OH
Posts: 2,128
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by SpoilsofWar
My utec says +.4 (absolute) when the car is off. I have not calibrated the map sensor though.
Which brings me to my question:
How do you use the map sensor calibration card to enter the values into the utec? For example, my calibration card states:
PSI Output
Cal 1 input: 1176 Cal 1 output: 7.13
Cal 2 input: 1725 Cal 2 output: 20.18
BAR Pressure Output
Cal 1 input: 875 Cal 1 output: 0.00
Cal 2 input: 1485 Cal 2 output: 1.00
So my question is how do these figures translate into the between 1 and 300 values that the utec wants you to enter for map calibration? The only thing I could think of was for the PSI numbers to divide input by output, because both of those would result in numbers between 1-300... But this is just a guess.
Which brings me to my question:
How do you use the map sensor calibration card to enter the values into the utec? For example, my calibration card states:
PSI Output
Cal 1 input: 1176 Cal 1 output: 7.13
Cal 2 input: 1725 Cal 2 output: 20.18
BAR Pressure Output
Cal 1 input: 875 Cal 1 output: 0.00
Cal 2 input: 1485 Cal 2 output: 1.00
So my question is how do these figures translate into the between 1 and 300 values that the utec wants you to enter for map calibration? The only thing I could think of was for the PSI numbers to divide input by output, because both of those would result in numbers between 1-300... But this is just a guess.
350Z UTEC Intercept 179
What can I say, I'm good with numbers.....
Actually, TurboXS provides a MAP calibration spreadsheet that you can enter the information in and it will spit out the calibration. I'm not sure why they can't just put the actual UTEC info on the calibration card.
03-26-2008, 06:13 PM
#20
Banned
iTrader: (1)
Join Date: Feb 2004
Location: Dayton, OH
Posts: 2,128
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by str8dum1
u shouldnt have to mess with the calibration. Performance factory said thats for the tunerxs, not the utec. Have you called Jermaine at TurboXS?
Mine is spot on.
Mine is spot on.