Si TRIM VORTECH.
#322
well every thing was going good till the serp belt almost threw itself off the pulley. also the cog idler pulley loosened up and started to eat into the s/c cog pulley. Sam is going to throw a new bando belt on tommorow and rectifie the cog issue. other than that he said everything is looking promising for good power numbers. the last pull was at 5500 rpm when the belt decided to go. he logged 12 lbs of boost at 5500 rpm! he is so glad i am running 100octane..... i will keep you posted with further info as i get it. i will post some pic's here shortly. OH and Sam sent one pic of the new custom exhaust setup from the rear. he said it is rediculously loud.........
Last edited by JET MECH; 02-10-2008 at 06:27 PM.
#323
New Member
iTrader: (11)
why do you run your cog idler like that? why not run the smooth pulley on teh smooth side of the belt. that seems to make more sense?
i also thought you did some crazy pulley mod as well (like the pic on page 16-- looks like a great idea!!) how could that throw the belt with extra guide pulleys? did the factory idler come loose?
12 psi at 5500 should be a beast!!
what size injectors are you using and do you have a return fuel system? i assume a walbro 255l.
i also thought you did some crazy pulley mod as well (like the pic on page 16-- looks like a great idea!!) how could that throw the belt with extra guide pulleys? did the factory idler come loose?
12 psi at 5500 should be a beast!!
what size injectors are you using and do you have a return fuel system? i assume a walbro 255l.
Last edited by str8dum1; 02-10-2008 at 06:41 PM.
#324
Originally Posted by str8dum1
why do you run your cog idler like that? why not run the smooth pulley on teh smooth side of the belt. that seems to make more sense?
i also thought you did some crazy pulley mod as well (like the pic on page 16-- looks like a great idea!!) how could that throw the belt with extra guide pulleys? did the factory idler come loose?
i also thought you did some crazy pulley mod as well (like the pic on page 16-- looks like a great idea!!) how could that throw the belt with extra guide pulleys? did the factory idler come loose?
no i did not do any pulley mod's i have a revup. the revup set up is a very good setup as is. yes i have 550 injectors, cjm stage 1 fuel system and 255lph pump. page one of this thread has a full list of my mod's.
#325
Registered User
iTrader: (14)
As much as everyone says that you will need a cog setup for high boost I am going to be glad that I don't have any on my car when the time comes for my high boost runs. They just seem to lead to problems.
Anyways, looks promising JET MECH! Lets hope everything goes well!
Anyways, looks promising JET MECH! Lets hope everything goes well!
#326
Registered User
Join Date: Feb 2004
Location: columbia md.
Posts: 1,041
Likes: 0
Received 0 Likes
on
0 Posts
"why do you run your cog idler like that? why not run the smooth pulley on teh smooth side of the belt. that seems to make more sense?"
It certainly will help grind the teeth down this way!
It certainly will help grind the teeth down this way!
#333
New Member
iTrader: (7)
Originally Posted by str8dum1
>>>> seems that AIT goes thru the roof with the SI blower......
#334
Originally Posted by jksstar
air temps were high, waiting to if Jet's car is going to do the same thing. I'm not going to say its the blower right now, it could be something small I over looked when I reinstalled everything. Sucks drove 1000 miles Sunday for it not to work
Last edited by JET MECH; 02-11-2008 at 11:07 AM.
#335
Originally Posted by jksstar
air temps were high, waiting to if Jet's car is going to do the same thing. I'm not going to say its the blower right now, it could be something small I over looked when I reinstalled everything. Sucks drove 1000 miles Sunday for it not to work
#336
the Si-trim should not be getting hotter! per the specs of the blower it is more efficient than the Sc-trim,has a higher rpm rating to it's peak efficencey and is rated at 78% isentropic efficiency versus the Sc-trim at 73%. this does not make sense? what is your cog setup,serp size and what rpm are you running it to? if you are running a 34 j/s cog 28 s/c cog and 2.87 to 6600 rpm you are overspeeding the blower quite a bit.
Last edited by JET MECH; 02-11-2008 at 11:10 AM.
#337
New Member
iTrader: (7)
Originally Posted by JET MECH
Sam mentioned that in the conversaton we had last night about the AIT. Sam stated that my AIT temps looked fine so far and the blower was not getting abnormaly hot. possibly due to my oil cooler i have installed. and possibly better due to the s/c oil cooler i fabricated and installed.
Could you keep me updated with the AIT. I would like to know if its the S/C or something I did.
#338
the burninator
iTrader: (11)
it shouldn't be getting hotter, but c'mon guys, you're pushing those blowers way hard.
peak efficiency doesn't mean a lot without seeing the compressor chart. I will bet my house you guys are both outside the peak efficiency range with how much boost you're using. You probably reach that peak 78% at around 8-9 psi around redline - meaning if you weren't spinning the blower nearly as hard and backed the pulley off a lot
IMO an intercooler upgrade and/or water/meth and/or more displacement are going to be needed to get the air temps lower. Me personally, I wouldn't even consider a larger blower without at least one of those things
peak efficiency doesn't mean a lot without seeing the compressor chart. I will bet my house you guys are both outside the peak efficiency range with how much boost you're using. You probably reach that peak 78% at around 8-9 psi around redline - meaning if you weren't spinning the blower nearly as hard and backed the pulley off a lot
IMO an intercooler upgrade and/or water/meth and/or more displacement are going to be needed to get the air temps lower. Me personally, I wouldn't even consider a larger blower without at least one of those things
Last edited by sentry65; 02-11-2008 at 11:17 AM.
#339
New Member
iTrader: (7)
Originally Posted by JET MECH
the Si-trim should not be getting hotter! per the specs of the blower it is more efficient than the Sc-trim,has a higher rpm rating to it's peak efficencey and is rated at 78% isentropic efficiency versus the Sc-trim at 73%. this does not make sense? what is your cog setup,serp size and what rpm are you running it to?
Last edited by jksstar; 02-11-2008 at 11:13 AM.