5AT build recommendations
#41
Registered User
iTrader: (2)
Join Date: Oct 2005
Location: The Valley, AZ
Posts: 1,220
Likes: 0
Received 0 Likes
on
0 Posts
Yup.... I am getting the older Haltech when my G gets there to Dynosty to work with my 5AT. It is finally getting picked up on Monday for the trip out there and she should be there in about 5-7 days after that.
The new Haltech only works on the 6MT. The old Haltech works for either. This is because torque management via the CAN bus is not (yet) supported in the new unit. The old unit relies on the stock ECU to transmit estimated torque values via CAN (and thus a working MAF is required to feed the stock ECU data).
#43
でたらめ検出器
iTrader: (1)
http://proefi.com/info/transmission-control-module/
#44
Registered User
iTrader: (2)
Join Date: Oct 2005
Location: The Valley, AZ
Posts: 1,220
Likes: 0
Received 0 Likes
on
0 Posts
Thanks, I brought that up to Hal and will get his opinion but I am putting the tuning into his hands and will go with what he suggests since he will be doing the tuning and he's one of the best in the business... I have no doubt in his abilities and the support he gives for the Haltech.
You don't have to get an "older" ProEFI and they're local to you. They also have a transmission control module with lots of nice features.
http://proefi.com/info/transmission-control-module/
http://proefi.com/info/transmission-control-module/
#45
でたらめ検出器
iTrader: (1)
Thanks, I brought that up to Hal and will get his opinion but I am putting the tuning into his hands and will go with what he suggests since he will be doing the tuning and he's one of the best in the business... I have no doubt in his abilities and the support he gives for the Haltech.
http://proefi.com/info/about-us/
You could have Hal do the build and then have Jason do the tune. Or better yet... I bet Saad Racing could do your build top notch. Then you could keep it all local.
Last edited by RudeG_v2.0; 02-08-2013 at 12:48 PM.
#46
Registered User
iTrader: (2)
I know a lot of peeps here on this forum support Hal. But you would be hard pressed to find a better or more experienced tuner than Jason Siebels, the owner of ProEFI. You could have Hal do the build and then have Jason do the tune. Or better yet... I bet Saad Racing could do your build top notch. Then you could keep it all local.
#47
Registered User
iTrader: (2)
Join Date: Oct 2005
Location: The Valley, AZ
Posts: 1,220
Likes: 0
Received 0 Likes
on
0 Posts
Build is already in progress and car goes on the transport on Monday, It's a done deal.
I know a lot of peeps here on this forum support Hal. But you would be hard pressed to find a better or more experienced tuner than Jason Siebels, the owner of ProEFI. Ask the guys at Sound Performance. He is very renowned and his reputation transcends the VQ platform.
http://proefi.com/info/about-us/
You could have Hal do the build and then have Jason do the tune. Or better yet... I bet Saad Racing could do your build top notch. Then you could keep it all local.
http://proefi.com/info/about-us/
You could have Hal do the build and then have Jason do the tune. Or better yet... I bet Saad Racing could do your build top notch. Then you could keep it all local.
#50
Registered User
iTrader: (2)
Join Date: Oct 2005
Location: The Valley, AZ
Posts: 1,220
Likes: 0
Received 0 Likes
on
0 Posts
I did quite a bit of research locally actually and that is one reason I am shipping her out there. Heck, I was going to have Intense do the install but they NEVER answer their phone and was not getting good vibes from them. Looked at 4 or so places and for peace of mind and not have to worry about finger pointing / pissn match from the engine builder to the installer if things went south on the install I decided to ship her out there for peace of mind and to me for peace of mind when dealing with a build such as this it is worth it. I called many places and got the best vibes and the service from Dynosty over the phone. Heck they actually answer the phone every time I call and don't mind going over things with you...
I am very comfortable with my decision.
I am very comfortable with my decision.
#51
でたらめ検出器
iTrader: (1)
I did quite a bit of research locally actually and that is one reason I am shipping her out there. Heck, I was going to have Intense do the install but they NEVER answer their phone and was not getting good vibes from them. Looked at 4 or so places and for peace of mind and not have to worry about finger pointing / pissn match from the engine builder to the installer if things went south on the install I decided to ship her out there for peace of mind and to me for peace of mind when dealing with a build such as this it is worth it. I called many places and got the best vibes and the service from Dynosty over the phone. Heck they actually answer the phone every time I call and don't mind going over things with you...
I am very comfortable with my decision.
I am very comfortable with my decision.
#52
Registered User
iTrader: (2)
Join Date: Oct 2005
Location: The Valley, AZ
Posts: 1,220
Likes: 0
Received 0 Likes
on
0 Posts
This way Dynosty can walk it thru from start to finish... Personally I just feel more comfortable with them seeing it thru and have no chances of finger pointing since it is their build, install and tune.
#53
でたらめ検出器
iTrader: (1)
Yeah... I like Tony and UMS A LOT and will probably go there for any future tuning I may need and almost went with them for the install (was really close actually) but I just did not want to get into any finger pointing if something went wrong with the install or if something went wrong upon start up.
This way Dynosty can walk it thru from start to finish... Personally I just feel more comfortable with them seeing it thru and have no chances of finger pointing since it is their build, install and tune.
This way Dynosty can walk it thru from start to finish... Personally I just feel more comfortable with them seeing it thru and have no chances of finger pointing since it is their build, install and tune.
#54
Damn Noobs
iTrader: (4)
Hmmmm.... I understand what you're saying, but it sounds like you didn't know about Saad Racing. There wouldn't be issues with their capabilities or with finger pointing between builder and tuner. I know Dynosty is the most popular shop on this forum at the moment and everyone seems to be pleased with him. But Hal/Dynosty isn't the only top notch shop that can walk it through from start to finish,(SP, VTR, PF Supercars) and you had some excellent options right here in AZ. Anyway... good luck.
Thread
Thread Starter
Forum
Replies
Last Post
350Z_Al
Exterior & Interior
133
10-29-2020 07:44 PM