PeterSellers

iTrader: (1)

I had the carbon gaskets that came with the ART pipes fail almost immediately. I replaced them with RTV and was fine for about 5K miles but just recently got another CEL for the bank 1 O2 sensors (same as before, indicative of another leak at those joints).

I think the exhaust manifolds are made of different metal than the ART pipes (or any other test pipes for that matter) which causes an issue when they heat up and expand at a different rate from the test pipes.

PeterSellers

iTrader: (1)

It's quite common for turbo charged cars to have higher peak torque than horsepower. It's very uncommon for a high revving N/A car to have that, however. Either something is wrong with the top-end of his car or the dyno was giving off an incorrect reading.

F2CMaDMaXX

iTrader: (2)

I understand it to be partially to do with the angle the gasses pass the joint, the extreme temp and pressure causes the issue with flat flange connections. The problem only exists on later models where the connection is different on the manifold.

Hydrazine

iTrader: (53)

Yes, they give higher absolute delta gains in TQ but they also make more HP than test pipes too.

Hydrazine

iTrader: (53)

If you need a replacement set of gasket just let me know. We have a new heavy duty gasket material that can take the heat.

We also have a new inlet design for the HR and VHR ART pipes that uses the stock metal crush ring. It will never leak or blow out.

AgentZ33

tony, when did the new inlet design take effect? if purchasing from vendor, will they have it? or will need to purchase through you to get the latest redesign?

PeterSellers

iTrader: (1)

I sent you a PM, I am definitely interested in the new gaskets.

Hydrazine

iTrader: (53)

They have been shipping for the last couple of weeks.

Hydrazine

iTrader: (53)

Replied.

sic6spd350z

PM sent about exhaust and art pipes

NFGZ

I purchased mine from a vendor around the 1st of july, he was out in California I wonder if I have them? Do you have pics of these to compare?

Also, If i wanted to put a wideband on my car, would I have to have a bung drilled into my ART pipes for my 07? I really dont want to have that done lol. Or would on the manifold or Y pipe suffice?

Duckeee

iTrader: (7)

i ordered mine last week and they came yesterday. also a california vendor.

F2CMaDMaXX

iTrader: (2)

The V3 pipes are for the HR motors and have a 'lip' on the end of the pipe that connects to the manifold.

If you post pics it can be confirmed.

Hydrazine

iTrader: (53)

Here you go.

This new gasket sealing design will never leak.

Hydrazine

iTrader: (53)

OFF TOPIC BUT VERY IMPORTANT

Please note if you have recently sent an email to Motordyne it may not have gone through. Our email volume is very high and for some reason it has corrupted Outlook.
I thought I had it fixed last week but apparently its not completely fixed. Not all emails are making it through. We are working to fix it now!

If you have any questions please feel free to call us (661) 298-7555.

Thank you!
Tony

NFGZ

Hey Tony, do you have any suggestions on the wideband question? Thanks for the photos!!

[QUOTE=Hydrazine;9806959]Here you go.

This new gasket sealing design will never leak.
[QUOTE]

Sweet! This is what mine looked like. Purchased from a cali vendor, I believe it was an infinity car dealership. Thanks man!

Hydrazine

iTrader: (53)

I suggest putting the wideband after the merge collector of the Y pipe.

xsackofricex

Hey Tony, does the DE have the new inlet design or is it only for the HRs?

F2CMaDMaXX

iTrader: (2)

Only the HR's need the flange, there is no problems at all on the DE's.

Duckeee

iTrader: (7)

I installed mine a few days ago on my HR with the new V3's and last night the car threw code P2A03. Should I suspect a leak somewhere? everything was fine prior to install, so I do not suspect the o2 sensors to be at fault.

edit: I used my cobb accessport to scan the code and it said something about control unit dtc code P2A03.