Where to get Replacement Studs for H&R 25mm Spacers?
06-29-2006, 06:26 PM
#2
Banned
iTrader: (25)
Join Date: Mar 2005
Location: 626 SOCAL!
Posts: 174
Likes: 0
Received 0 Likes
on
0 Posts
What's your definition of moderately priced?
Most tuner lugs like Muteki start at around $40.
Then the higher end quality stuff like Rays and Work are around $120.
Then the highest quality gangster stuff like Kics Project R40/R26 are around $200.
If you can find the knurl size of the spacer stud you might just be able to get a replacement one at a Pepboys or such for cheap.
Most tuner lugs like Muteki start at around $40.
Then the higher end quality stuff like Rays and Work are around $120.
Then the highest quality gangster stuff like Kics Project R40/R26 are around $200.
If you can find the knurl size of the spacer stud you might just be able to get a replacement one at a Pepboys or such for cheap.
06-29-2006, 07:27 PM
#3
Originally Posted by A Spec Products
What's your definition of moderately priced?
Most tuner lugs like Muteki start at around $40.
Then the higher end quality stuff like Rays and Work are around $120.
Then the highest quality gangster stuff like Kics Project R40/R26 are around $200.
If you can find the knurl size of the spacer stud you might just be able to get a replacement one at a Pepboys or such for cheap.
Most tuner lugs like Muteki start at around $40.
Then the higher end quality stuff like Rays and Work are around $120.
Then the highest quality gangster stuff like Kics Project R40/R26 are around $200.
If you can find the knurl size of the spacer stud you might just be able to get a replacement one at a Pepboys or such for cheap.
06-30-2006, 10:13 AM
#5
Banned
iTrader: (25)
Join Date: Mar 2005
Location: 626 SOCAL!
Posts: 174
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by sq40
$40 doesnt sound too bad. From what I understand it is pretty hard to find replacement studs without going Nismo. 20 Nismo Studs will run me around $120, which I think is way too much... The H&R studs seem to be very soft though.. But, they will fit perfectly and I will only need 10.
06-30-2006, 10:16 AM
#6
Originally Posted by A Spec Products
Nismos are extended though (60mm iirc?), I assume the H&R studs are stock length (50mm?)
About those lugs, Do you sell them?
06-30-2006, 11:08 AM
#7
Banned
iTrader: (25)
Join Date: Mar 2005
Location: 626 SOCAL!
Posts: 174
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by sq40
I beleive so. I contacted H&R about 10 Minutes ago, They told me I can get them through my distrubutor (which was performance Nissan) for about $2.00 each. So that wont be too bad.
About those lugs, Do you sell them?
About those lugs, Do you sell them?
Yes I sell all the lugs I listed, PM me.
Trending Topics
07-01-2006, 03:10 AM
#8
Sponsor
Performance Nissan
Performance Nissan
iTrader: (11)
Join Date: Oct 2003
Location: So-Cal - Ready to go?
Posts: 8,783
Likes: 0
Received 2 Likes
on
2 Posts
I think you called and spoke to justin when I was passing through the office today?
When he asked me about it he wasnt sure if it was the studs on the actual spacer its self or in your wheel hubs...
If H&R says the studs in the spacer its self can be replaced with a factory hub bolt, then you can either use the factory Z hub bolts or the extended NISMO ones...
PM me if you need any more info...
the more detail you give me the better I can help you...
When he asked me about it he wasnt sure if it was the studs on the actual spacer its self or in your wheel hubs...
If H&R says the studs in the spacer its self can be replaced with a factory hub bolt, then you can either use the factory Z hub bolts or the extended NISMO ones...
PM me if you need any more info...
the more detail you give me the better I can help you...
Thread
Thread Starter
Forum
Replies
Last Post
