Strange Problem w/ APS TT
#21
Registered User
iTrader: (3)
Join Date: Jan 2005
Location: NY
Posts: 1,895
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://my350z.com/forum/images/icons/icon1.gif)
I remember someone else in the same sort of situation and had the RPS package as well. It was someone on the boards but I cannot recall who it was...Hopefully they can chime in if they see this...GL
#22
Registered User
iTrader: (1)
Join Date: Aug 2003
Location: Ottawa, ON, Canada
Posts: 505
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://my350z.com/forum/images/icons/icon1.gif)
Originally Posted by ht4
Thanks for the idea- We considered that might be the issue so we totaly disabled the VDC system but the problem remianed... ![Frown](https://my350z.com/forum/images/smilies/frown.gif)
The guys who did my install tell me that because of the splines in the steering shaft hook-up, it is pretty hard to mess up so that also tells me that is likely not the problem... In any case, assuming it is the issue, do you know how to reset the VDC system?
![Frown](https://my350z.com/forum/images/smilies/frown.gif)
The guys who did my install tell me that because of the splines in the steering shaft hook-up, it is pretty hard to mess up so that also tells me that is likely not the problem... In any case, assuming it is the issue, do you know how to reset the VDC system?
#23
Registered User
Thread Starter
iTrader: (1)
Join Date: Nov 2005
Location: Bethesda, MD
Posts: 971
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://my350z.com/forum/images/icons/icon1.gif)
Originally Posted by Madelinot
For the VDC light, just one rib off on the steering shaft and it can cause problems (been through this before). You can't mess it up completely, but it's actually easy to get it slightly wrong. Check it out.
Mine works fine under all conditions except WOT (or close to it) and whenever it hits around 6psi. It will redline with no problems even under about 85%... It's only under full power- that is why I am leaning towards a MAF voltage issue.
#24
Registered User
iTrader: (1)
Join Date: Aug 2003
Location: Ottawa, ON, Canada
Posts: 505
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://my350z.com/forum/images/icons/icon1.gif)
Originally Posted by ht4
What sort of symptoms did you have?
Best of luck and let us know...
#25
Registered User
Thread Starter
iTrader: (1)
Join Date: Nov 2005
Location: Bethesda, MD
Posts: 971
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://my350z.com/forum/images/icons/icon1.gif)
Update:
Swapped out the wiring harness with no effect
unichip X1 driver was adjusted with no effect
Swapped out the unichip X1 driver with no effect
Called RPS who confirmed that they have NO COMPLAINTS from my batch of flywheels with regard to CAS issues (and since they are made in large batchs where are all are cut from the same piece of metal, if one had an issue, 40 would likely have the same issue)
VDC was TOTALLY disabled without effect
We are running out of ideas!!! Your help would be highly appreciated.
Swapped out the wiring harness with no effect
unichip X1 driver was adjusted with no effect
Swapped out the unichip X1 driver with no effect
Called RPS who confirmed that they have NO COMPLAINTS from my batch of flywheels with regard to CAS issues (and since they are made in large batchs where are all are cut from the same piece of metal, if one had an issue, 40 would likely have the same issue)
VDC was TOTALLY disabled without effect
We are running out of ideas!!! Your help would be highly appreciated.
Thread
Thread Starter
Forum
Replies
Last Post