MREV+ Dyno Tested On The 287 HP Engine!
Registered User
Joined: Oct 2005
Posts: 83
Likes: 0
From: Carson, CA
I'll be installing my machined lower plenum this weekend. Tony is a great guy to talk to and I can personally vouch for his hard work. I'll list my impressions later on this thread. Also, it was a pleasure meeting all the other guys at church's over the weekend.
-Tom
-Tom
it doesn't really matter.. as long as we get the dynos before tony decides to release them.. that way we can make up our minds then order
Originally Posted by MustGoFastR
Million dollar question actually is: when is somebody gonna post up the freakin' dynos?!
edited to change last word from "mrev" to "revup". 2 hours of sleep last night, does it show, lol?
Last edited by mikead_99; May 1, 2006 at 12:25 PM.
So did anyone dyno the MREV2 with a Crawford plenum? I'm curious if the gains will be there, as milling down the tops of those front runners is to account for the slope of the stock plenum, which is fixed on the top side with the Crawford...
Originally Posted by MustGoFastR
So did anyone dyno the MREV2 with a Crawford plenum? I'm curious if the gains will be there, as milling down the tops of those front runners is to account for the slope of the stock plenum, which is fixed on the top side with the Crawford...
Originally Posted by Wired 24/7
Nobody in the group had an aftermarket plenum. You have a good point though. Just a suggestion: perhaps if you are not satisfied with the crawford plenum, you could always swap back with stock and install the mrev v2...
Thread Starter
MOTORDYNE-MY350Z SPONSOR
iTrader: (53)
Joined: Jul 2004
Posts: 4,399
Likes: 9
From: L.A. California
Originally Posted by mikead_99
Yup, and looking to see/hear how plenum+spacer does on revup.
edited to change last word from "mrev" to "revup". 2 hours of sleep last night, does it show, lol?
edited to change last word from "mrev" to "revup". 2 hours of sleep last night, does it show, lol?
Originally Posted by Hydrazine
If you can be the first to install it on the dyno I'll give you an additional $100 rebate.
Post your results here and on G35 driver.
Post your results here and on G35 driver.
Thread Starter
MOTORDYNE-MY350Z SPONSOR
iTrader: (53)
Joined: Jul 2004
Posts: 4,399
Likes: 9
From: L.A. California
Yes. For a dyno install with a Crawford Cast Plenum.
EDIT: The same applies for a 1/2" spacer.
Offer won't last long! Once enough dynos come in to establish the expected performance, its done!
Test conditions must be typical for the average user. (S.T.P. - IE no extreme altitudes or temperatures)
FI is a go!
EDIT: The same applies for a 1/2" spacer.
Offer won't last long! Once enough dynos come in to establish the expected performance, its done!
Test conditions must be typical for the average user. (S.T.P. - IE no extreme altitudes or temperatures)
FI is a go!
Last edited by Hydrazine; May 1, 2006 at 04:45 PM.
Originally Posted by Hydrazine
Yes. For a dyno install with a Crawford Cast Plenum.
EDIT: The same applies for a 1/2" spacer.
Offer won't last long! Once enough dynos come in to establish the expected performance, its done!
Test conditions must be typical for the average user. (S.T.P. - IE no extreme altitudes or temperatures)
FI is a go!
EDIT: The same applies for a 1/2" spacer.
Offer won't last long! Once enough dynos come in to establish the expected performance, its done!
Test conditions must be typical for the average user. (S.T.P. - IE no extreme altitudes or temperatures)
FI is a go!
Registered User
Joined: Jul 2003
Posts: 73
Likes: 0
From: Florida
Originally Posted by MustGoFastR
Well, that's just it, I am happy with my aftermarket upper plenum. I'm just wondering whether or not the MREV 2 is going to add additional gains or not...
I'm in the same boat; waiting to see if gains are realized with a Crawford Plenum.
