[DFW]: DFW's Lounge
General & Tech Moderator
MY350Z.COM
MY350Z.COM
iTrader: (4)
How many miles you have? I know my tranny is doomed. I notice sometimes it doesn't engage at first going from reverse to drive.
who all has to work tomorrow?
No work tomorrow...need the time to get better because of this cold that I acquired from my wife . THANK YOU MLK for your dream. Now I get to stay home and heal my body and enjoy the time off / $$$.
TRAV are you sure that your issue is not the oem CSC (concentric slave cylinder) and not the clutch. Your HR has known issues with weak CSC which is internal to the transmission versus being slapped on the side of the tranny like older models. That is the part you linked earlier.
https://my350z.com/forum/vq35hr/3281...-cylinder.html
TRAV are you sure that your issue is not the oem CSC (concentric slave cylinder) and not the clutch. Your HR has known issues with weak CSC which is internal to the transmission versus being slapped on the side of the tranny like older models. That is the part you linked earlier.
https://my350z.com/forum/vq35hr/3281...-cylinder.html
New Member
iTrader: (11)
it is more than likely the slave cylinder, it went out on me about 3 months after i bought the car, i think i checked it before but i fell out of the range. jake do you think we can do the swap out orr what are your thoughts??
General & Tech Moderator
MY350Z.COM
MY350Z.COM
iTrader: (4)
why rebuild and waste so much money. Just slap a low mileage tranny and call it a day. I can't imagine a used tranny being more than $500 - $750 for an auto. I can't imagine the cost of parts and labor to repair/rebuild a 160k miles old transmission.
Ask jake for his contact in grand prairie for the junk yard and start looking around. I would only rebuild if you are trying to have your tranny hold more power. If you are stock or pretty much stock and even some FI members. I would stick with an auto tranny, new fluids, transgo and some sort of cooler and call it a day.
60 k miles
http://dallas.craigslist.org/mdf/pts/3559313648.html
80k
http://dallas.craigslist.org/ftw/pts/3544672310.html
Ask jake for his contact in grand prairie for the junk yard and start looking around. I would only rebuild if you are trying to have your tranny hold more power. If you are stock or pretty much stock and even some FI members. I would stick with an auto tranny, new fluids, transgo and some sort of cooler and call it a day.
60 k miles
http://dallas.craigslist.org/mdf/pts/3559313648.html
80k
http://dallas.craigslist.org/ftw/pts/3544672310.html
Last edited by faiz23; 01-20-2013 at 12:01 PM.
your slave should be covered under extended warranty but the clutch is not. Your issue is slave and should be taken care of by nissan or your warranty. I bet you the clutch is perfectly fine. Jake should be able to do it since you are practically doing a clutch job. He has done plenty of clutch jobs, master cylinders and even slave cylinders (older style). It will be slightly harder due to routing cables from internal slave to master but I think it should be doable. I would trust jake if he is comfortable. Regardless I would be pushing for my extended warranty to cover it using the recall letter as proof that this is not a wear and tear but design defect.
General & Tech Moderator
MY350Z.COM
MY350Z.COM
iTrader: (4)
In a couple years I'm definitely buying a used tranny/engine and building both.
I swear my car is a ticking time bomb.
I swear my car is a ticking time bomb.
STU that is something I have wanted to do forever (just engine rebuild). Even spoke to jake about picking up a nice rev up core and rebuilding it on the side with help from jake and ilya. He tells me I am paranoid and to just drive my car lolz. I like picking up slickdeals and have noticed tons of rev up cores cheap along with cheap forged pistons, forged rods and other parts during part out time. I am here for the long run and would love to make a slickdeal forged engine and learn a ton in the process. Alas time is money and I have neither
i will call them again, but since the master and slave have already been replaced with OEM, and went out again a little over a year later and 23k miles, i am really skeptical about putting the same POS in there again
Sleeps in 350Z
iTrader: (5)
Shoot I would let them do it again to avoid the cost now. Then when it's time for a clutch upgrade you could throw in the better parts.
i will call them and nissan tomorrow, if nissan with throw the after market one in instead of the factory one, i will see if the warranty will cover labor..... makes the most sense
i guess one good thing about being stuck home, got apt cleaned and all my laundry done.... trying to find the positive in this
General & Tech Moderator
MY350Z.COM
MY350Z.COM
iTrader: (4)
STU that is something I have wanted to do forever (just engine rebuild). Even spoke to jake about picking up a nice rev up core and rebuilding it on the side with help from jake and ilya. He tells me I am paranoid and to just drive my car lolz. I like picking up slickdeals and have noticed tons of rev up cores cheap along with cheap forged pistons, forged rods and other parts during part out time. I am here for the long run and would love to make a slickdeal forged engine and learn a ton in the process. Alas time is money and I have neither
yeah when i first got it i was all over the place, live in irving and worked in downtown, longview many times, san angelo, i was making trips from irving to mansfield about 4 times a week, it has really slowed down ....now i put maybe 800-1000 miles a month. i usually hit the time frame to get oil changed before mileage now
and technically it has been close to year and half now, bought it in july 2011
and technically it has been close to year and half now, bought it in july 2011
Last edited by travlee; 01-20-2013 at 03:03 PM.
Sleeps in 350Z
iTrader: (24)
Join Date: Mar 2007
Location: Flower Mound , TX
Posts: 5,745
Likes: 0
Received 0 Likes
on
0 Posts
Gonna just Track, and AutoX with the RPF1's,,,what the hell ?
I also still have my MB Battles with the RS-3's on them.....deciding whether or not to sell them or put some better rubber on them.
That sucks....do you drive it in the Triptonic mode all the time ?
Also do you drive it like a manual and down shift ?
Down shifting in it in Triptonic mode will kill your Tranny !
I have to work....SUCKS !
Last edited by fithamoto; 01-20-2013 at 03:07 PM.
are the 9.5 +15 on all corners?
I have to work too. Jealous for the folks who get off.
Chris DD'ing on RS3? BALLER! What's wrong with DD'ing the Hankook's and using the MB's with RS3 for track?
Chris DD'ing on RS3? BALLER! What's wrong with DD'ing the Hankook's and using the MB's with RS3 for track?