usingthejohn

iTrader: (11)

I had the whole thing installed. But what I'm talking about is here:

https://my350z.com/forum/7001303-post1.html

If you look at photo #1, the pulley on the actual s/c needs to be installed the opposite way. I called Vortech, who confirmed the same; he also mentioned that the pulley needs to be removed via impact wrench, which I don't have.

- bigc -

iTrader: (18)

gotcha. you should still be able to break that pulley loose using a strap wrench to hold it steady. your choice though.

usingthejohn

iTrader: (11)

Ah, OK....I'll try that first. Worse things worse, Gearheinz performance said he would be willing to do it for me this week; i just need to find time to bring it to him.

350z006

iTrader: (79)

Are you able to drive your car to Long Beach? I've taken the cog pulley off my blower plenty of times, just need a cog belt and the right tools....btw, do you have a revup or non-revup?

usingthejohn

iTrader: (11)

I could drive it to Long Beach; just leave the cog-belt off, right?

350z006

iTrader: (79)

Right...it's not like you can put it on properly in the first place...Also, bring your cog belt...

You still have my cell #? send me a text....

usingthejohn

iTrader: (11)

bollocks...no i don't have your cell number. maybe i can FINALLY pick up your fuel rails, too.

shoot me a PM with your number

TunerMax

iTrader: (2)

Any good "DIY" Links for this install? Primarily trying to get together more specific tool's needed list, As I'm driving from my place in Canada to The U.S. to install this in a friends garage this weekend. He has no tools, I need to bring whatever I might need.

I've seen a bunch of threads on the installa nd read the instructions many times, just looking for a tools needed list mainly.

350z006

iTrader: (79)

Here's a good guide that I used when I first installed my Vortech:

https://my350z.com/forum/forced-indu...nks-of-fi.html

And superchargersonline.com has good DIY as well, including tools needed:

http://www.superchargersonline.com/i...age=page&id=51

SkyZ33

iTrader: (1)

Driving to WA?

TunerMax

iTrader: (2)

Thx dude great links. Neither have a part list that is more specific than the vortech one though. No biggie, the whole thing looks like a cake walk anyways, I'm just trying to over prepare lol.

Upstate NY

usingthejohn

iTrader: (11)

OK, I got the correct pulley installed onto my blower, thanks to Gearheinz.

Now, another issue (albeit it, minor at this time). But Last night, i installed the 2.87 pulley on my bracket, however even just hand-tightening the bolt, the pulley would NOT turn at all; installing the 3.12 pulley in place of the 2.87 enabled me to freely spin the pulley.

The problem I'm encountering is similar to this:
https://my350z.com/forum/forced-indu...not-right.html

So, what is the problem? The thread above didn't really cite what needed to be done. I was thinking of having it milled down, but after reading the above thread, i'm not sure i thats the accurate way to go.

Thanks for the help, My350z. Looking forward to joining the FI ranks once I get the above hiccup cured.

str8dum1

iTrader: (11)

yes it needs to be machined down

usingthejohn

iTrader: (11)

OK, wasn't too sure if that was the route you went with. Did you just machine down the flag side of the pulley (closest to the bracket) and (i'm sure i know the answer is yes) but any machine shop can do this? IIRC, you mentioned it needed to be machined down by 0.90", correct?

- bigc -

iTrader: (18)

this diagram shows what needs to be removed

usingthejohn

iTrader: (11)

How much material is that then? And thanks for that diagram.

**EDIT** i'm at work, so i don't have the pulley in front of me, but i'm assuming that the material to be removed just needs to follow the diagram, and down flush with the face of the pulley, correct?

- bigc -

iTrader: (18)

yep, just get it down flush to the face of the pulley. the part that is rubbing is the area highlighted in yellow.

usingthejohn

iTrader: (11)

looks like my blower will need a rebuild...not surprising, since i bought it used. I was wondering, has anyone on here ever rebuilt their blower themselves? It isn't an issue of me being cheap; rather, i want to learn to do as much on my car as possible. i've seen a couple DIY threads online via other forums (s2ki, moddedmustangs) and curious if anyone here has done so themselves?

EDIT: Found the following link; curious if anyone else here has gone the DIY route on the rebuild?

https://my350z.com/forum/engine-driv...haft-seal.html

TunerMax

iTrader: (2)

Got it this weekend but vortech sent the wrong pulley and blower trim.... Looks like this won't be running till at least next season

evilscorp

Anyone know if Vortech will supply the chargecooler in black? About to order the tuner kit but would prefer a black one and do many of you guys leave the two installation brackets attached to the chargercooler to give it more support on the bottom? Just looks a bit weak with only one side supported, but may have issue with my Zspeed undertray fouling if I leave the install brackets on for support.