Official STS Rear Mount Turbo Discussion Thread
#2341
#2345
Registered User
Join Date: Dec 2006
Location: Canada
Posts: 165
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://my350z.com/forum/images/icons/icon1.gif)
Hey guys havent been around for a while hope everyone is good. Just a quick question if anyone can help....With my aem tru boost an 8.5 psi spring... in second gear i hit no more then 6 psi and in third gear no more then 8-9 psi and 4th gear goes to 10.5 psi regardless what I set the bc too... (I know a gdbc will help but short on cash right now) I was wondering could it be due to a bad tune>? Iam running stock kit with hks bov aem tru boost (8.5 psi spring) and heat wrapped the exhaust. Should I bother to get it retuned by someone else? My a/f generally sits around 10.8-11.2 in wot because i wanted to run a bit on the safer side. Should I lean out a bit more for more power? Anyone else have a similar problem? Any thoughts? Thanks!
#2346
Registered User
iTrader: (2)
Join Date: Nov 2005
Location: NYC
Posts: 2,252
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://my350z.com/forum/images/icons/icon1.gif)
Hey guys havent been around for a while hope everyone is good. Just a quick question if anyone can help....With my aem tru boost an 8.5 psi spring... in second gear i hit no more then 6 psi and in third gear no more then 8-9 psi and 4th gear goes to 10.5 psi regardless what I set the bc too... (I know a gdbc will help but short on cash right now) I was wondering could it be due to a bad tune>? Iam running stock kit with hks bov aem tru boost (8.5 psi spring) and heat wrapped the exhaust. Should I bother to get it retuned by someone else? My a/f generally sits around 10.8-11.2 in wot because i wanted to run a bit on the safer side. Should I lean out a bit more for more power? Anyone else have a similar problem? Any thoughts? Thanks!
#2347
Registered User
Join Date: Dec 2006
Location: Canada
Posts: 165
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://my350z.com/forum/images/icons/icon1.gif)
Thanks AthenG! I noticed with the bc off the boost runs lower in gear 1 an 2. It does not go higher then 5psi..weird. But I will re chek the vac lines and will possibly retune on tuesday.I have a feelin ill have to get the apexi inorder to fix this boost problem.
#2348
Registered User
Join Date: Nov 2008
Location: HAWAII CUZ!!!
Posts: 8
Likes: 0
Received 0 Likes
on
0 Posts
#2349
Registered User
![Default](https://my350z.com/forum/images/icons/icon1.gif)
apexi will hit 10psi in first gear but you MUST get the speed signal hooked up which is a bit of a trick.
#2350
Registered User
iTrader: (2)
Join Date: Nov 2005
Location: NYC
Posts: 2,252
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://my350z.com/forum/images/icons/icon1.gif)
Finally got a chance to replace the STS FMIC with the ARC-made IC that comes with the PE TT. It's wider and taller than the STS IC but it's a Bar/Plate design vs. Tube/Fine that comes with the STS. The actual core size is 22.3" (W) x 10.3" (H) x 2.5" (D). I can’t believe how heavy the STS IC was… I'll post some pix of the inside of both IC but the STS definetly has smaller air passage way vs the PE IC. The overall design of the PE TT look much more efficient than most of the IC I have seen.
At first I was worried about the pressure drop because it is bigger but it's not the case. The IC barely heat up vs. the STS. I did a little driving and I have noticed some spool difference. I haven’t touched my Utec boost mapping and did some driving and the first thing I noticed is that I'm hitting 9psi on my 8psi map. I had to bring down the BCS duty cycle to -10 just to get back to 8psi. I'm also on stock CAT right now so spool is slower but I noticed I'm hitting the same boost/rpm when I had my Test Pipe. I only did a 20 min of driving but I'll try to retune my car again in the next week or two. I'll get a better gauge once I re-tune my car because I already know how the STS react on different load/gear.
I dont have a pix yet of the IC on my car but this is what it look like.
At first I was worried about the pressure drop because it is bigger but it's not the case. The IC barely heat up vs. the STS. I did a little driving and I have noticed some spool difference. I haven’t touched my Utec boost mapping and did some driving and the first thing I noticed is that I'm hitting 9psi on my 8psi map. I had to bring down the BCS duty cycle to -10 just to get back to 8psi. I'm also on stock CAT right now so spool is slower but I noticed I'm hitting the same boost/rpm when I had my Test Pipe. I only did a 20 min of driving but I'll try to retune my car again in the next week or two. I'll get a better gauge once I re-tune my car because I already know how the STS react on different load/gear.
I dont have a pix yet of the IC on my car but this is what it look like.
![Name: PE_FMIC.jpg
Views: 70
Size: 42.9 KB](https://my350z.com/forum/attachments/forced-induction/414990d1501884683-official-sts-rear-mount-turbo-discussion-thread-pe_fmic.jpg)
#2353
Registered User
Join Date: Dec 2006
Location: Canada
Posts: 165
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://my350z.com/forum/images/icons/icon1.gif)
I think this will be my altimate solution for the boost situation. I'll sell the AEM truboost and grab the apexi.. the speed signal wire wont be a problem since my decks vehicle dynamic already hooks up to it. THanks!
#2355
New Member
iTrader: (1)
Join Date: Jun 2008
Location: wichita,ks
Posts: 341
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://my350z.com/forum/images/icons/icon1.gif)
ok guys haven't posted here for a while been saving up for this turbo kit. lot of money for a single turbo lol.. but might be worth it in the end but need to ask how hard is the install for this kit just asking i full bolt ons which parts should i keep and which should i part out here is the list.
i know the intake is out and the exhaust is gone but heres the rest kinetix v+ plenum, ground wires, lightweight pulleys stock size, strup headers, kinetix hfc, jwt clutch and aluminum flywheel, and cobb tuner.
i know the intake is out and the exhaust is gone but heres the rest kinetix v+ plenum, ground wires, lightweight pulleys stock size, strup headers, kinetix hfc, jwt clutch and aluminum flywheel, and cobb tuner.
#2356
Registered User
![Default](https://my350z.com/forum/images/icons/icon1.gif)
I would lose the plenum and get a spacer, lose the ground wires just for the extra cash and trade the hfc's for some tp's and lose the cobb since you will be going with utec. I don't think anyone has done headers yet with this setup. I've been interested to see how they would do, although i think equal length headers would be best.
#2357
New Member
iTrader: (1)
Join Date: Jun 2008
Location: wichita,ks
Posts: 341
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://my350z.com/forum/images/icons/icon1.gif)
wouldn't the plenum be the same as the spacer anyways? and why swap my hfc for the test pipes? i know antheng told me about the headers that slow my spool up or something like that and what gauges do you recommend i was looking at a fuel press. gauge and a/f gauge, and boost gauge, what do you think. and is it hard to install the kit yourself sts company told me its a full bolt on?
#2358
![Default](https://my350z.com/forum/images/icons/icon1.gif)
wouldn't the plenum be the same as the spacer anyways? and why swap my hfc for the test pipes? i know antheng told me about the headers that slow my spool up or something like that and what gauges do you recommend i was looking at a fuel press. gauge and a/f gauge, and boost gauge, what do you think. and is it hard to install the kit yourself sts company told me its a full bolt on?
#2359
Registered User
![Default](https://my350z.com/forum/images/icons/icon1.gif)
Finally got a chance to replace the STS FMIC with the ARC-made IC that comes with the PE TT. It's wider and taller than the STS IC but it's a Bar/Plate design vs. Tube/Fine that comes with the STS. The actual core size is 22.3" (W) x 10.3" (H) x 2.5" (D). I can’t believe how heavy the STS IC was… I'll post some pix of the inside of both IC but the STS definetly has smaller air passage way vs the PE IC. The overall design of the PE TT look much more efficient than most of the IC I have seen.
At first I was worried about the pressure drop because it is bigger but it's not the case. The IC barely heat up vs. the STS. I did a little driving and I have noticed some spool difference. I haven’t touched my Utec boost mapping and did some driving and the first thing I noticed is that I'm hitting 9psi on my 8psi map. I had to bring down the BCS duty cycle to -10 just to get back to 8psi. I'm also on stock CAT right now so spool is slower but I noticed I'm hitting the same boost/rpm when I had my Test Pipe. I only did a 20 min of driving but I'll try to retune my car again in the next week or two. I'll get a better gauge once I re-tune my car because I already know how the STS react on different load/gear.
I dont have a pix yet of the IC on my car but this is what it look like.
![](http://i71.photobucket.com/albums/i124/athenG/PE_FMIC.jpg)
At first I was worried about the pressure drop because it is bigger but it's not the case. The IC barely heat up vs. the STS. I did a little driving and I have noticed some spool difference. I haven’t touched my Utec boost mapping and did some driving and the first thing I noticed is that I'm hitting 9psi on my 8psi map. I had to bring down the BCS duty cycle to -10 just to get back to 8psi. I'm also on stock CAT right now so spool is slower but I noticed I'm hitting the same boost/rpm when I had my Test Pipe. I only did a 20 min of driving but I'll try to retune my car again in the next week or two. I'll get a better gauge once I re-tune my car because I already know how the STS react on different load/gear.
I dont have a pix yet of the IC on my car but this is what it look like.
![](http://i71.photobucket.com/albums/i124/athenG/PE_FMIC.jpg)
#2360
OGPremierMafia
![](https://my350z.com/forum/images/ranks/premier.gif)
iTrader: (16)
Join Date: Feb 2005
Location: Cincinnati OH
Posts: 5,106
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://my350z.com/forum/images/icons/icon1.gif)
not to thread jack, but for the $ I would go with Sasha's mid mount kit. Better response, more power, no boost bleeding, second to none customer service. Not to mention he's a Z guy himself.