SnyperZ

iTrader: (10)

MPG went up about 5 but it still surges in 2 of the exact same spots.. in 4th gear at exactly 41mph(right around 2500) and again at 51mph(right around 3) right when im at around -9hg


Im still waiting for MRC to call me back with a date to get it tuned..i might just try somewhere else.

rcdash

iTrader: (18)

It's not because of your AFR targets. You have to adjust the base fuel table. You should see your wideband read out of spec in conjunction with the hesitation. You could go to -9 at the rpms you specified, but you're tuning blind without the wideband...

SnyperZ

iTrader: (10)

Good point. I guess ill get off my LAZY *** and do it tomorrow.

SnyperZ

iTrader: (10)

Is the meth injection control ready yet? Which meth injection do you guys recommend? I dont want it to make power..but more as an added safety blanket.

IIQuickSilverII

iTrader: (13)

any of the aquamist kits would work

350zzzgunnar

is a tuning needed after installing a injection kit?

Dynosty

iTrader: (27)

Meth control will work as a simple on/off switch controlled by 3 AND/OR statements. For a safety blanket something simple like an AEM kit would work, but if you are wanting to maximize power I would suggest something a little more advanced like an Aquamist setup. I would advise going over the tune with the addition of meth, especially if you are injecting a large amount.

SnyperZ

iTrader: (10)

can you post up a diagram of the vacuum routing of the boost controler?

Dynosty

iTrader: (27)

A diagram comes with the solenoid kit, but the quick rundown for typical external wastegate(s) such as Tial:
Port 1 = Boost pressure source (intake manifold or turbo)
Port 2 = Top port on wastegate(s)
Port 3 = Vent / Breather

The bottom/side port on the wastegate must have constant boost source (intake manifold or turbo)

* Always monitor boost when making changes to the wastegate or boost controller. With Haltech Platinum, use the over-boost limiter for added protection.

SnyperZ

iTrader: (10)

Isnt there two different ways to hook it up? One more high boost and one for low? Also, im hooking up the wideband and you said somethign about calibrating it...how exactly do I do that? I put the guage in the center console..it looks so nice.

SnyperZ

iTrader: (10)

Oh And that overboost feature works great by the way, I played around with the settings to see how it works, its kind of scary how it just shuts down the engine when your not expecting it haha.

Dynosty

iTrader: (27)

Use the method I just posted. If you max out boost on that method (normally slightly more than double your wastegate spring), it's time for a spring upgrade.

Once you have hooked your wideband(s) up to Haltech, you need to connect to the ECU manager and change the data under Calibrations: O2 Sensor 1 and O2 Sensor 2. You need these calibrations to match the data supplied by Innovate for your wideband analog output. (LC-1 output 2 is set at 0v = 7.35AFR, 5v = 22.39AFR from the factory). Depending on where you grounded the wideband you may have to offset the voltage slightly to get the AFRs perfect.

SnyperZ

iTrader: (10)

Ok. How exactly do I find out the exact numbers?

Dynosty

iTrader: (27)

What exact numbers?

To view the calibrated o2 sensors, use channels:
Calibrations - O2 Sensor 1
Calibrations - O2 Sensor 2

To view the raw voltage inputs use channels:
AV6
AV8

SnyperZ

iTrader: (10)

Ok, so do the same thing needed to calibrate the TPS and pedal

SnyperZ

iTrader: (10)

nm

SnyperZ

iTrader: (10)

Ok the guage is reading way off. The ecu is reading the correct number but the actual guage itself is reading off into the 20s...anyone have any idea why?

Dynosty

iTrader: (27)

The gauge read proper before? If so, what did you change?

You can use a multimeter to verify voltages if you need. Output 2 from Innovate (brown wire) feeds your gauge and Haltech o2 input 1 and 2.

SnyperZ

iTrader: (10)

EDIT for stupidity(sorry for dragging the thread out)

SnyperZ

iTrader: (10)

I love this software. =)