FAQ: Official wheel "SPACER" thread!
any ideas?
Registered User
Joined: May 2014
Posts: 2,892
Likes: 277
From: arizona
Im new to this as well so hopefully this is just straight forward but i got some rohana rc22 not staggered on a deal. Im going to call them and see if they have the rear spoke clearance or not.
So i now have (4) 20" rims already tired. Width is 9" for all four. Bolt pattern; 5x 114.3 and they're offset is +35 all around
I basically test fit these onto my 350z that is lowered on Bilstein pss10s but setup to almost a maximum height. I think im going to need my fenders rolled if im correct? And my rears fit fine with no spacer (they clear my brembos) but the front hit against my caliper by about 2mm when i tried test fitting with a 8mm spacer.
I just want these rims to fit and not rub but also look good any ideas on the perfect spacer combo i need? I know i need a minimum of 12mm on the fronts to clear.
Is it smart to run spacers in the front and not back if theyre not staggered?
I also already purchase hubcentric rings in the proper bore size. I bought 2 sets to be sure (one plastic gorilla brand) one aluminim set off ebay both at the bore sizes 66.1 to 73.1 (which is what my aftermarket rims are)
So suggestions on spacers please
So i now have (4) 20" rims already tired. Width is 9" for all four. Bolt pattern; 5x 114.3 and they're offset is +35 all around
I basically test fit these onto my 350z that is lowered on Bilstein pss10s but setup to almost a maximum height. I think im going to need my fenders rolled if im correct? And my rears fit fine with no spacer (they clear my brembos) but the front hit against my caliper by about 2mm when i tried test fitting with a 8mm spacer.
I just want these rims to fit and not rub but also look good any ideas on the perfect spacer combo i need? I know i need a minimum of 12mm on the fronts to clear.
Is it smart to run spacers in the front and not back if theyre not staggered?
I also already purchase hubcentric rings in the proper bore size. I bought 2 sets to be sure (one plastic gorilla brand) one aluminim set off ebay both at the bore sizes 66.1 to 73.1 (which is what my aftermarket rims are)
So suggestions on spacers please
So many things wrong w8th these wheels....
Registered User
Joined: Dec 2015
Posts: 31
Likes: 0
From: Ann arbor
If only this was an option ha. What are the proper offsets + specs on rohana rc22
I would optimally have bought 20 x 9 for the front and 20 x 10 or 20 x 11 for the rears. Might upgrade in the future. But trying to figure out if i can fit these well
I would optimally have bought 20 x 9 for the front and 20 x 10 or 20 x 11 for the rears. Might upgrade in the future. But trying to figure out if i can fit these well
Registered User
Joined: May 2014
Posts: 2,892
Likes: 277
From: arizona
Can you fit it? Sire, should you? No...
Registered User
Joined: Dec 2015
Posts: 31
Likes: 0
From: Ann arbor
Registered User
Joined: Dec 2015
Posts: 31
Likes: 0
From: Ann arbor
Registered User
Joined: May 2014
Posts: 2,892
Likes: 277
From: arizona
Registered User
Joined: Dec 2015
Posts: 31
Likes: 0
From: Ann arbor
Im set on the model and style though. I want rc22s; i think a new set of thrm cost $1600 for the rims alone and i can sell these for about $1250 easy. But what spacers and such would i need if i want this set to fit until then
Registered User
Joined: Dec 2015
Posts: 31
Likes: 0
From: Ann arbor
Registered User
Joined: Dec 2015
Posts: 31
Likes: 0
From: Ann arbor
Well does anyone know what i need to do to perfectly fit thesr on; otherwise gunna need to buy new ones n sell these. And im going to have a seperate 18" set for when i go track
Registered User
Joined: May 2014
Posts: 2,892
Likes: 277
From: arizona
Registered User
Joined: May 2014
Posts: 2,892
Likes: 277
From: arizona
No one knows how flush you want it, how lower you are, chances are youll hit the fenders going over a bump, but just to answer your question, youll need a spacer in the 85mm range
Registered User
Joined: Dec 2015
Posts: 31
Likes: 0
From: Ann arbor
Isnt it just 1 spacer in the front though or do i just space at 20/25mm. You guys know more as to what wheel will fit in with what spacer size. Basically
If someone can tell me exactly what spacer i need for front n back that would be perfect. Ill find out if the back of the rims have space for the oem bolts
If someone can tell me exactly what spacer i need for front n back that would be perfect. Ill find out if the back of the rims have space for the oem bolts
http://rohanawheels.com/wheel/rc22/
Registered User
Joined: Dec 2015
Posts: 31
Likes: 0
From: Ann arbor
As i said my offet is +35
also what would be the proper rim size / offset for these in 20" then incase i want to order new ones. I basically want a 20" set. A 18" track set n i already have a 17" winter set lol